manualshive.com logo in svg

ATI Technologies Q45P, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
ATI Technologies Q45P Скачать руководство пользователя страница 39

ATI 

Q45P pH System  

 

Part 6 

–System Maintenance

 

 

39 

O&M Manual 
Rev-B (7/15) 

 

MESSAGE 

DESCRIPTION 

 

POSSIBLE CORRECTION 

Sensor High 

The raw signal from the sensor is too 
high. 

  Check wiring connections to sensor. 

Sensor Low 

The raw signal from the sensor is too 
low. 

  Check wiring connections to sensor. 

pH too High 

The pH reading is > 14.00 pH. 

  The pH reading is over operating limits. 

pH too Low 

The pH reading is < 0.00 pH. 

  The pH reading is under operating limits. 

Temp High 

The temperature reading is > 110 ºC. 

  The temperature reading is over operating 

limits.  Check wiring and expected temp 
level.  Perform RTD test as described in 
sensor manual.  Recalibrate sensor 
temperature element if necessary. 

Temp Low 

The temperature reading is < -10 ºC 

  The temperature reading is under operating 

limits.  Check wiring and expected temp 
level.  Perform RTD test as described in 
sensor manual.  Recalibrate sensor 
temperature element if necessary. 

TC Error 

TC may be open or shorted. 

  Check sensor wiring and perform RTD test 

as described in sensor manual. 

Meas Break 

Leakage detected on measuring 
electrode of sensor. 

  Measuring electrode glass may be cracked 

or broken.  Electrical noise may falsely trip 
this diagnostic.  Turn off glass diagnostic 
feature and see if sensor operates correctly.  
If it does not, sensor must be replaced. 

Ref Break 

Leakage detected on reference 
electrode of sensor. 

  Reference glass electrode may be cracked 

or broken.  Electrical noise may falsely trip 
this diagnostic.  Turn off glass diagnostic 
feature and see if sensor operates correctly.  
If it does not, sensor must be replaced. 

 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание Q45P
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды