manualshive.com logo in svg

ATI Technologies Q45P, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
ATI Technologies Q45P Скачать руководство пользователя страница 33

ATI 

Q45P pH System  

 

Part 5 

–Calibration

 

 

33 

O&M Manual 
Rev-B (7/15) 

buffers are not present in this menu, the user can override the automatic values 
and enter arbitrary values.  However, the highest accuracy is provided when the 
user  selects  and  uses  buffers  from  this  pre-defined  table  list.    With  the  pre-
defined  buffers,  the  temperature  variations  in  the  buffer  are  automatically 
compensated  for  during  the  calibration  process.    If  the  buffer  data  is  manually 
entered, the calibration buffer sample must be very temperature stable to achieve 
the same degree of accuracy.

 

 

Procedure 

 

1. 

Remove sensor from application.  Rinse and clean if necessary.

 

 

2. 

Allow sensor to temperature equilibrate with the buffer as best as possible.  With 
the sensor coming from an application solution that differs greatly in temperature 
from  the  buffer,  the  user  may  have  to  wait  as  much  as  20  minutes  for  this  to 
occur.

 

 

3. 

Scroll to the CAL menu section using the MENU key and press ENTER or the UP 
arrow key.  

Cal pH

 will then be displayed.

 

 

4. 

Press the ENTER key.  The screen will display a flashing 1 for 1-point or a 2 for 
2-point  calibration.    Using  the  UP  arrow  key,  set  for  a  2-point  calibration  and 
press ENTER.

 

 

 

 

 
 
 

 

5. 

The display will prompt the user to place the sensor in the first buffer and press 
ENTER.    If  the  sensor  has  been  placed  into  this  buffer  already,  once  the 
temperature has stabilized, press ENTER to continue. 

6. 

The present pH value will be displayed and the secondary line of the display will 
flash 

Wait

  for  approximately  10-15  seconds.    At  this  time  the  system  is 

attempting to recognize the first buffer value from the two values entered into the 
Set Buffers selection. 

7. 

The  screen  will  display  the  buffer  value  to  be  used  for  calibration.    If  the  user 
chooses  to  change this  value,  the arrow  keys  can  be  used to modify  the  value.  
Any value between 0.00 and 14.00 pH can be entered.  After adjusting this value, 
or to accept the automatic value, press ENTER. 

8. 

The  system  now  begins  acquiring  data  for  the  calibration  value  of  this  buffer 
point.  As data is gathered, the units for pH and temperature may begin to flash.  
Flashing  units  indicates  that  this  parameter  is  unstable.    The  data  point 

Содержание Q45P
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды