ATH-Heinl ATH-Four Lift 55 страница 27 Скачать руководство пользователя

Страница: 27 / 64

Manufacturer ATH-Heinl GmbH & CO.KG

- 27 -

3.0

OPERATION

3.1

Operating Instructions

for

Lifting Platform

Risks to People and the Environment



Falling of loads or parts



Crushing and shearing points when moving the lifting platform



Danger due to uncontrolled moving parts

Protective Measures and Rules of Conduct

Before starting work:



Lifting platforms may only be used independently by trained persons over the age
of 18 who have been instructed in writing.



When working with more than one person, a supervisor must be appointed



Daily functional check



Observe the manufacturer’s operating instructions

During operation:



Pay attention to crush and shear points in the environment



Do not load the lifting platform above the permitted maximum load



Do not lift people



Do not shake the lifting platform, avoid rocking.



When lowering, do not stand in the lifting platform movement area



Arrange regular checks of the lifting platform

Response to faults and hazards



In case of fault, stop the lifting platform immediately



Secure against further use



Report defects to the installer or manufacturer

First Aid



Inform first aiders (see alarm/emergency plan)



Treat injuries immediately



Enter into the accident book



Contact emergency services for serious injuries

Emergency number:

_____________

Ambulance service: _______________

Maintenance



Repair only by instructed and trained persons



Disconnect or secure the lifting platform from the mains power supply for set-up,

adjustment, maintenance or servicing



Clean the lifting platform after operation and check the hydraulic level



Annual check

of the lifting platform by an authorised and trained person

Company:

Place of work:

Operation:

Date:

Signature:

Содержание ATH-Four Lift 55




















































Результаты поиска

Содержание ATH-Four Lift 55

Отзывы:

Похожие инструкции для ATH-Four Lift 55

Бренды по названию

Популярные бренды

ATH-Heinl ATH-Four Lift 55, Руководство по эксплуатации

Результаты поиска

Содержание ATH-Four Lift 55

Отзывы:

Похожие инструкции для ATH-Four Lift 55

Бренды по названию

Популярные бренды