Ateis PRIMA-VA/R Скачать руководство пользователя страница 31

Страница: 31 / 75

Activity Hold Time

Read / Write Time before audio input release if no modulation detection

Monitored

Read / Write Pilot ton detection – Fault report if no pilot ton detection

Monitoring Threshold

Read / Write Pilot ton level to be detected

Monitoring Time-out

Read / Write Time before fault report if no pilot tone detection

Security

Read / Write

Audio input is allowed to be played even if mains power supply is
missing

Evacuation

Read / Write Evacuation LEDs are lighting and evacuation relay is active when

audio input is routed

Click on Apply changes to save modifications.

Click on Back to list to jump to

Basic config > Audio page.

6.4.2.

To configure front microphone

Click on

Front Microphone.

AGC Max Gain

and

AGC Target Level

are displayed only if

Auto Gain Control

option is selected.

Static Gain

is displayed only if

Auto Gain Control

option is not selected.

Parameter

Access

Description

Sensitivity

Read / Write

Maximum input level before overload

Auto Gain Control

Read / Write

Automatic adjustment of front microphone signal to maintain a
constant signal level

AGC Max Gain

Read / Write

Maximal gain applied to front microphone signal

AGC Target Level

Read / Write

Target level after adjustment

Noise Gate

Read / Write

Front mute if audio signal is lower than fixed threshold – Noise
gate threshold = -70 dB

Содержание PRIMA-VA/R












































































Результаты поиска

Содержание PRIMA-VA/R

Отзывы:

Похожие инструкции для PRIMA-VA/R

Бренды по названию

Популярные бренды

Ateis PRIMA-VA/R, Руководство пользователя

Результаты поиска

Содержание PRIMA-VA/R

Отзывы:

Похожие инструкции для PRIMA-VA/R

Бренды по названию

Популярные бренды