ATD Tools ATD-3130, Руководство по эксплуатации, Страница: 8 / 36

8
t
Do not expose cylinders to electricity of
any kind.
t
Do not use a cylinder or its contents for
anything other than its intended use. Do
not use as a support or roller.
t
Do not locate cylinders in passageways
or work area where they may be struck.
t
Do not use a wrench or hammer to open
a cylinder valve that cannot be opened
by hand. Notify your supplier.
t
Do not modify or exchange gas cylinder
fittings.
t
Do not deface or alter name, number or
other markings on a cylinder. Do not rely
on cylinder color to identify the contents.
t
Do not connect a regulator to a cylinder
containing gas other than that for which
the regulator was designed.
t
Do not attempt to make regulator repairs.
Send faulty regulators to manufacturer’s
designated repair center for repair.
t Do not attempt to lubricate a regulator.
t Always change cylinders carefully to pre-
vent leaks and damage to their walls,
valves, or safety devices.
t Always secure cylinders with a steel chain
so that they cannot be knocked over.
t Always protect a cylinder, especially the
valve, from bumps, falls, falling objects
and weather. Remember that gasses in
the cylinders are under pressure and
damage to a regulator can cause the
regulator or portion of the regulator to
be explosively ejected from the cylinder.
t
Always make certain the cylinder cap is
securely in place on the cylinder, when-
ever the cylinder is moved.
t
Always close the cylinder valve and
immediately remove a faulty regulator
from service, for repair, if any of the fol-
lowing conditions exist.
t
Gas leaks externally.
t
Delivery pressure continues to rise with
down stream valve closed.
t
The gauge pointer does not move off the
stop pin when pressurized or fails to
return to the stop pin after pressure is
released.
WARNING
This product contains chemicals, including
lead, or otherwise produces chemicals
known to the State of California to cause
cancer, birth defects and other reproductive
harm. Wash hands after Handling.
(California Health & Safety Code Sec.
25249.5 et seq.)
ADDITIONAL SAFETY INFORMATION
For additional information concerning weld-
ing safety, refer to the following standards
and comply with them as applicable.
t
ANSI Standard Z49.1 – SAFETY IN
WELDING AND CUTTING – obtainable
from the American Welding Society, 550
NW Le Jeune Road, Miami, FL 33126
Telephone (800) 443-9353, Fax (305)
443-7559 – www.amweld.org or
www.aws.org
t
ANSI Standard Z87.1 – SAFE PRACTICE
FOR OCCUPATION AND EDUCATION-
AL EYE AND FACE PROTECTION –
obtainable from the American National
Standards Institute, 11 West 42nd St.,
New York, NY 10036 Telephone (212)
642-4900,
Fax (212) 398-0023 – www.ansi.org
t NFPA Standard 51B – CUTTING AND
WELDING PROCESS – obtainable from
the National Fire Protection Association,
1 Batterymarch Park, P.O. Box 9101,
Quincy, MA 02269-9101 Telephone
(617) 770-3000
Fax (617) 770-0700 – www.nfpa.org
t
OSHA Standard 29 CFR, Part 1910,
Subpart Q., WELDING, CUTTING AND
BRAZING – obtainable from your state
OSHA office or U.S. Dept. of Labor
OSHA, Office of Public Affairs, Room
N3647, 200 Constitution Ave.,
Washington, DC 20210 –
www.osha.gov
t
CSA Standard W117.2 – Code for
SAFETY IN WELDING AND CUTTING. –
obtainable from Canadian Standards
Association, 178 Rexdale Blvd.,
Etobicoke, Ontario M9W 1R3 –
www.csa.ca
t
American Welding Society Standard
A6.0. WELDING AND CUTTING CON-
TAINERS WHICH HAVE HELD COM-
BUSTIBLES. – obtainable from the
American Welding Society, 550 NW Le
Jeune Road, Miami, FL 33126
Telephone (800) 443-9353, Fax (305)
443-7559 – www.amweld.org or
www.aws.org