Asus P5LD2-DH Скачать руководство пользователя страница 50

Страница: 50 / 78

2-6

Chapter 2: BIOS setup

2..4

ASUS CrashFree BIOS 2 utility

The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS

file when it fails or gets corrupted during the updating process. You can update a

corrupted BIOS file using the motherboard support CD or the floppy disk that contains

the updated BIOS file.

Recovering the BIOS from a floppy disk

To recover the BIOS from a floppy disk:

Turn on the system.

Insert the floppy disk with the original or updated BIOS file to the floppy disk drive.

The utility displays the following message and automatically checks the floppy

disk for the original or updated BIOS file.

Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...

Restart the system after the utility completes the updating process.

Bad BIOS checksum. Starting BIOS recovery...

Checking for floppy...

Floppy found!

Reading file “P5LD

FM.ROM”. Completed.

Start flashing...

When found, the utility reads the BIOS file and starts flashing the corrupted BIOS

file.

DO NOT shut down or reset the system while updating the BIOS! Doing so can cause

system boot failure!

•

Prepare the motherboard support CD or the floppy disk containing the updated

motherboard BIOS before using this utility.

•

Make sure that you rename the original or updated BIOS file in the floppy disk to

P5LD2FM.ROM.

Содержание P5LD2-DH















































































Результаты поиска

Содержание P5LD2-DH

Отзывы:

Похожие инструкции для P5LD2-DH

Бренды по названию

Популярные бренды

Asus P5LD2-DH, Руководство пользователя

Результаты поиска

Содержание P5LD2-DH

Отзывы:

Похожие инструкции для P5LD2-DH

Бренды по названию

Популярные бренды