Asus P5LD2-DH Скачать руководство пользователя страница 49

Страница: 49 / 78

ASUS P5LD2-FM/DH/VP

2-5

The utility returns to the DOS prompt after the BIOS update process is

completed. Reboot the system from the hard disk drive.

A:\>afudos /iP5LD2FMDH.ROM

AMI Firmware Update Utility - Version 1.10

Reading file ..... done

Erasing flash .... done

Writing flash .... 0x0008CC00 (9%)

Verifying flash .. done

A:\>

Copy the AFUDOS utility (afudos.exe) to the bootable floppy disk you created

earlier.

Boot the system in DOS mode, then at the prompt type:

afudos /i[filename]

where [filename] is the latest or the original BIOS file on the bootable

floppy disk.

A:\>afudos /iP5LD2FMDH.ROM

AMI Firmware Update Utility - Version 1.10

Reading file ..... done

Erasing flash .... done

Writing flash .... 0x0008CC00 (9%)

Updating the BIOS file

To update the BIOS file using the AFUDOS utility:

Visit the Fujitsu Siemens Computers website (www.fujitsu-siemens.com) and

download the latest BIOS file for the motherboard. Save the BIOS file to a bootable

floppy disk.

A:\>afudos /iP5LD2FMDH.ROM

The utility verifies the file and starts updating the BIOS.

Do not shut down or reset the system while updating the BIOS to

prevent system boot failure!

Write the BIOS filename on a piece of paper. You need to type the exact

BIOS filename at the DOS prompt.

Содержание P5LD2-DH















































































Результаты поиска

Содержание P5LD2-DH

Отзывы:

Похожие инструкции для P5LD2-DH

Бренды по названию

Популярные бренды

Asus P5LD2-DH, Руководство пользователя

Результаты поиска

Содержание P5LD2-DH

Отзывы:

Похожие инструкции для P5LD2-DH

Бренды по названию

Популярные бренды