Asus P5LD2-DH Скачать руководство пользователя страница 44

Страница: 44 / 78

1-32

Chapter 1: Product introduction

•

Power/Soft-off button (Black 2-pin PWRSW )

This connector is for the system power button. Pressing the power

button turns the system ON or puts the system in SLEEP or SOFT-OFF

mode depending on the BIOS settings. Pressing the power switch for

more than four seconds while the system is ON turns the system OFF.

•

System Power LED connector (2-pin PLED)

This 2-pin connector is for the system power LED. The system power

LED lights up when you turn on the system power, and blinks when

the system is in sleep mode.

•

Reset button (Blue 2-pin RESET )

This 2-pin connector is for the chassis-mounted reset button for

system reboot without turning off the system power.

•

Hard disk drive activity (Red 2-pin IDELED)

This 2-pin connector is for the HDD Activity LED. Connect the HDD

Activity LED cable to this connector. The IDE LED lights up or flashes

when data is read from or written to the HDD.

12. System panel connector (10-1 pin F_PANEL)

This connector supports several chassis-mounted functions.

The sytem panel connector is color-coded for easy connection. Refer to

the connector description below for details.

P5LD2-FM/DH/VP System Panel Connector

Requires an ATX power supply.

D-

PWRLED

D+

F_PANEL

D+

D-

RESET

IDELED

PWRSW

-F

Содержание P5LD2-DH















































































Результаты поиска

Содержание P5LD2-DH

Отзывы:

Похожие инструкции для P5LD2-DH

Бренды по названию

Популярные бренды

Asus P5LD2-DH, Руководство пользователя

Результаты поиска

Содержание P5LD2-DH

Отзывы:

Похожие инструкции для P5LD2-DH

Бренды по названию

Популярные бренды