Astria Fireplaces Scorpio Series Скачать руководство пользователя страница 53

Operation 

900683-00, 05/2017

Innovative Hearth Products
Scorpio™ Series Direct-Vent Gas Fireplaces

53

Continuous Pilot Ignition Switch

Fireplaces with an electronic gas valve have a continuous pilot ignition (CPI) controlled by the remote

This switch allows the pilot to be switched from intermittent mode to continuous mode:

•  Intermittent Mode—The pilot is extinguished when the fireplace is OFF.

•  Continuous Mode—The pilot stays ON when the fireplace is OFF.

In periods of extreme cold, condensation may form on the glass door when the fireplace is OFF and the pilot is in 

intermittent mode. Also, with the pilot in intermittent mode, the fireplace may 

cycle startup

 (i.e., the pilot and burner ignite, 

but the burner extinguishes and reignites several times until the flue reaches the temperature for proper drafting).

•  To save energy—switch to intermittent mode. 

•  For a standing pilot that will help prevent glass door condensation and cycle startup—switch to continuous mode.

NOTE: Continuous mode is indicated by a pilot that comes ON and remains lit when the fireplace is OFF.

Traditional Only: Installing the Firebox Liners

1. 

Remove the three (3) optional firebox liner panels from the packing materials if purchased.

2. 

Carefully position the rear panel, upper edge first, in the firebox against the rear wall.

3. 

While holding the rear panel, carefully position the left side panel in the firebox. 

4. 

Carefully position the right side panel in the firebox.

NOTE: Do not force the panels. Excessive force may cause breakage. If the panels are correctly positioned, they will 

fit snugly in place.

 

Contemporary Only: Installing the Glass Media

1. 

Install the glass media in the recessed area between the front and rear floors. See 

Figure 43B

 on 

Page 54

.

NOTE: 35” fireplaces require less than a full bag of glass media. 40” fireplaces require an entire bag of media.

2. 

Spread the glass media in a thin layer, evenly over the burner. CAUTION: Ensure the glass media does not fall 

inside the bracket or through the pilot hole 

(see

 

Figure 43B

 

on

 

Page 54).

NOTE: Do NOT mound the media.

Installing the Backup Batteries

With a battery backup, electronic fireplaces can automatically switch to battery power. In the event of a power outage, this 

allows ON/OFF operation (without blower functionality). Install new batteries before every burn season. 

1.  Open the lower control panel, and locate the battery holder 

(See Figure 39)

.

2.  Install four (4) AA batteries in the battery holder.

3.  Close the lower control panel.

Some parts have been removed for clarity

Figure 39 - Battery Holder (in control compartment)

Figure 40 - Switches (in control compartment)

Battery

Holder

Learn Switch is for programming the remote (see 

instructions provided with the remote control)

IPI Switch is for continuous pilot or standing pilot

Hi-Low Switch controls the main burner flame height

ON/OFF Switch turns the burner on and off

Содержание Scorpio Series











































































Отзывы: