manualshive.com logo in svg

Astria Fireplaces Scorpio Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Astria Fireplaces Scorpio Series Скачать руководство пользователя страница 44

Installation 

900683-00, 05/2017

Innovative Hearth Products
Scorpio™ Series Direct-Vent Gas Fireplaces

44

Table 28 - Air Shutter Adjustment Guidelines

Amount of Primary 

Air

Flame Color

Air Shutter Adjustment

If air shutter is 

closed too far

Flame will 

be orange

Air shutter gap should be increased

If air shutter is 

open too far

Flame will 

be blue

Air shutter gap should be decreased

Air Shutter

Adjustment 

Rod Down  

(Fully-Open 

Position)

Burner 

Tube

Adjustment 

Rod Up 

(Fully-Closed 

Position)

Adjustment 

Set-Screw

Figure 34 - Air Shutter Adjustment Rod

1.  Move the adjustment rod down to increase air flow and up to decrease it. The rod is located in the lower control 

compartment. Position the air shutter to the factory setting

 (Table 29)

.

2.  Light the fireplace. Follow the lighting procedure on the lighting label in the control compartment or 

Pages 68-69

.

3.  Allow the burner to operate for at least fifteen (15) minutes while observing the flame continuously to ensure that 

the proper flame appearance is achieved 

(Figure 35)

. If the following conditions are present, adjust accordingly.

•  If flame appears weak or sooty, adjust the air shutter, incrementally, to a more open position until the proper 

flame appearance is achieved.

•  If flame remains blue, adjust the air shutter, incrementally, to a more closed position until the proper flame 

appearance is achieved.

4.  When satisfied that the burner flame appearance is normal, reinstall the lower control compartment door, then 

proceed to finish the installation.

Figure 35 - Burner Flame Appearance

Table 29 - Main Burner Shutter Opening—Factory Setting

Models

Natural Gas

Propane

All

1/16”  

(1.6 mm)

1/8”  

(3.2 mm)

Traditional - Charred Oak Logs

Traditional - Driftwood Logs

Contemporary

Содержание Scorpio Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды