background image

Page: 3

 Version 3 : 01-04-016

Caution:

 The unit is fitted with a safety mechanism, if the unit encounters an obstruction under 

the front portion of the basin whilst travelling downwards it will automatically stop. Pressing the ‘Up’ 

button will allow the obstruction to be removed. Care should be taken to ensure that 

whilst the basin assembly is moving downwards there are no obstructions left directly 

beneath the basin or rise & fall unit as the safety mechanism is designed to stop the 

unit only when the front of the basin is lifted. 

If both the ‘Up’ and Down’ buttons are pressed at the same time the unit will not move.

Troubleshooting

In the unlikely event that problems occur with the unit, carry out the following easy checks to 

determine whether or not an engineer is required.

Fault:  

The rise and fall unit does not travel up or down

Cause:  

The mains power supply has been disconnected for some time and the unit’s batteries are 

now flat.

Remedy: Examine the green LED fitted to the right hand side of the unit. If the green LED is not 

illuminated neither mains electricity nor battery backup are supplying the unit. Examine the mains 

fuses/circuit breakers and reset as necessary and ensure that mains voltage is fully reconnected 

then press the reset button situated next to the handset connector. If the LED fails to illuminate an 

electrician needs to ensure that mains electrical supply is available at the fused spur (a fuse may have 

blown elsewhere in the circuit).

Fault: 

The rise and fall unit travels upwards but not downwards.

Cause:  

There is an obstruction underneath the basin.

Remedy:  Depress the ‘Up’ button on the handset to gain clearance from the obstruction and then 

remove the obstruction. The rise & fall unit may then resume normal function.

If the problem persists after carrying out these remedies, please

contact Astor-Bannerman on the number on the back page:

Cleaning

The basin and vanity top may be cleaned using most mild cleaning agents. Chemical agents must 

not be used, i.e., drain cleaners, acetone, oven cleaners or acids. The rise and fall unit, mirror and 

handset should be cleaned using a warm soapy solution and rinsed with a damp cloth. Attention 

should always be paid to instruction labels on the outside of cleaning agent containers.

The waste plug

To the rear of the tap block is a small rod with a ‘knob’ fitted to the top. This can be raised and 

lowered to open or close the waste plug as required.

Содержание ABW6













Отзывы: