background image

A33606-PCI-60-6A SAS-2 Expander User Manual 

 

 

4

 

Copyright © 2014 by Astek Corporation.  All rights reserved 

Ver. A 

DOCUMENT 90-000186, VERSION C (1/15/2011) 

This document describes Astek’s 36-port 6Gbit/s Serial-attached SCSI (SAS) expander and will remain the official reference 
source for all revisions/releases of this product until rescinded by an update. 

To receive product literature, visit us at 

http://www.astekcorp.com

. 

 

DISCLAIMER 

Astek Corporation reserves the right to make changes to any products herein at any time without notice.  Astek does not assume 
any responsibility or liability arising out of the application or use of any product described herein, except as expressly agreed to 
in writing by Astek; nor does the purchase or use of a product from Astek convey a license under any patent rights, copyrights, 
trademark rights, or any other of the intellectual property rights of Astek or third parties.  Astek products are not intended for 
use in life-support appliances, devices, or systems.  Use of any Astek product in such applications without written consent of 
the appropriate Astek officer is prohibited. 

 

TECHNOLOGY LICENSES 

The hardware and/or software described in this document are furnished under a license and may be used or copied only in 
accordance with the terms of such license. 

 

REGULATOR COMPLIANCE 

Note: The A33606-PCI has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of 
the FCC Rules. These Limits are designed to provide reasonable protection against harmful interference when the equipment is 
operated in its installation. This equipment generates, uses, can radiate radio frequency energy, and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications. If this equipment does cause 
harmful interference the user will be required to correct the interference. 

The A33606-PCI has been tested and meets the safety requirements of IEC/EN 60950-1. 

 

COPYRIGHT NOTICE 

Copyright © 2010 by Astek Corporation.  All rights reserved. 

 

TRADEMARK ACKNOWLEDGMENT 

The Astek logo design is the trademark or registered trademark of Astek Corporation.  LSI, LSI Logic, and MPT are the 
trademarks or registered trademarks of LSI, Inc.  All other brand and product names may be trademarks of their respective 
companies. 

 

Содержание A33606-PCI-60-6A SAS-2




























Отзывы: