ASTECH VLM500 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 29

ASTECH VLM500 Скачать руководство пользователя страница 24

VLM60 User Manual

Parameterization

page 24

ASTECH GmbH

Store

The command permanently saves the currently set parameters in the device. The command is protected by a
password (command

Password

).

store

Only if this command is executed, the current parameter settings are retained even after the device is
switched off.

TComp

The command outputs the value for the temperature compensation in PPM/K. The compensation value is
used for a temperature-independent determination of the velocity.

tco

mp

The setting is made at the factory and cannot be changed.

Testmeasure

The command starts a test output of the measured values. This output has a fixed structure and is composed
of the values x-speed, y-speed, x-length, y-length, measuring rate, illuminance, overexposure and
underexposure. The output ends automatically after 60s.

testm

easure [c]

c = c (no abort after 60 s)

Sending ESC to the device aborts the test output. Unlike other commands, the line termination here is only a
"CR" (carriage return).

When using the VLMTool, the output values are shown in a window display.

Type

The command outputs the type of the connected VLM60.

type

The setting is made at the factory and cannot be changed.

«
...
22
23
24
25
26
...
»

Содержание VLM500






























Отзывы:

Нет отзывов