ASTECH VLM500 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 29

ASTECH VLM500 Скачать руководство пользователя страница 11

Parameterization

VLM60 User Manual

ASTECH GmbH

page 11

4

Parameterization

4.1

Command input and VLMTool

The parameterization or command input can be done with any terminal program (e.g. HTerm). For
parameterization of the VLM60, connection 3 is connected to a USB interface of a Windows PC via a programming
cable..

In the command line, enter as many characters as necessary until the syntax is unambiguous. In the following
command documentation, the characters that must be entered at least for one command are printed in bold.
Parameters are separated from the command by spaces. The decimal point is used to separate places before and
after the decimal point. When entering commands without parameters, the current value of this parameter is
displayed. In order to save parameter changes permanently, the

store

command must be used.

The VLMTool is installed under Windows 10/11. The installation data is located on the USB stick included in the
scope of delivery or can be downloaded from the Internet at

https://www.astech.de/en/download.html

. The

program starts with 9600 baud. The standard baud rate of the VLM60 is 115200 baud. When the software is
started for the first time, the COM port and the baud rate must be set in the VLMTool. If these settings have
been made correctly, the serial number and the firmware version are displayed at the top of the program
window.

Figure 9: VLMTool

«
...
9
10
11
12
13
...
»

Содержание VLM500






























Отзывы:

Нет отзывов