Assa Abloy Yale Delayed Egress Скачать руководство пользователя

Страница: 9 / 16

For technical support contact Yale

at 800.438.1951 or [email protected]

An ASSA ABLOY Group brand

80-9470-0162-000 10/18

Delayed Egress

Exit Device

Installation Instructions

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

Non-ElectroLynx Door Prep

Figure 8

NOTE:
1.  Do not scale drawing.
2.  Dimensions are in inches (mm).
3.  LHR H.M. opening shown. Details are

typical for all opening materials (both

hands).

4. This preparation is an addition to

preparation shown on device template.

5. See device template to locate

centerline of device template.

6. Shields for wring access

recommended for insulated and

composite doors.

7. Locate and prepare wiring access

holes when installing device.

Exit Device

7100 Series

7200 Series

Dim. A

2-5/16 (59)

1-11/16 (43)

Содержание Yale Delayed Egress

















Результаты поиска

Содержание Yale Delayed Egress

Отзывы:

Похожие инструкции для Yale Delayed Egress

Бренды по названию

Популярные бренды

Assa Abloy Yale Delayed Egress, Руководство по установке

Результаты поиска

Содержание Yale Delayed Egress

Отзывы:

Похожие инструкции для Yale Delayed Egress

Бренды по названию

Популярные бренды