Assa Abloy SARGENT 10X Series страница 7 Скачать руководство пользователя

Страница: 7 / 8

Copyright © 2021 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part
without the express written permission of SARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

A8286 04/21

10X Line

Installation Instructions

Cylindrical Lockset

Miscellaneous Options

Tailpiece

1. Provided less core.

2. Tailpiece included with lock.

3. Attach tailpiece to Schlage

LFIC and insert into the lever.

1. Provided less core.

2. Depress cap pin and unscrew end cap to

remove tailpiece from competitor cylinder.

3. Insert new tailpiece, in orientation shown.

4. Re-assemble end cap over new tailpiece.

Lever to Accept Schlage

LFIC (SF- Option)

Lever to Accept Schlage

or Yale

Fixed Core Cylinder (30- or YC- Option)

Lever to Accept Yale

LFIC (YRC- Option)

Competitor’s
Cylinder

Cap Pin

End Cap

1. Provided less core.

2. Slide provided spacer over tailpiece

3. Insert driver assembly into back of core.

Содержание SARGENT 10X Series









Результаты поиска

Содержание SARGENT 10X Series

Отзывы:

Похожие инструкции для SARGENT 10X Series

Бренды по названию

Популярные бренды

Assa Abloy SARGENT 10X Series, Руководство по установке

Результаты поиска

Содержание SARGENT 10X Series

Отзывы:

Похожие инструкции для SARGENT 10X Series

Бренды по названию

Популярные бренды