background image

IS93  07/21

Copyright © 2021, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in 

part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

23

5 8

"

600mm

LENGTH OF MORTISE

22

1 2

"

572mm

LENGTH OF TRACK

1

1 4

"

32mm

VARIES WITH

DOOR THICKNESS

19"

483mm

CUTOUT ON STOP SIDE ONLY

4X 1/4-20 UNC X 5/8"

OR #14 X 1-1/2" FOR WOOD

1"

25mm

6

3 8

"

162mm

16

1 8

"

410mm

21

1 2

"

546mm

1

3 4

"

44mm

 MIN.

SEE NOTE 7

7 8

"

22mm

4

15 16

"

125mm

PULL SIDE

STOP SIDE

6

1 4

"

159mm

21

7 8

"

556mm

21

1 8

"

537mm

3 8

"

10mm

5 8

"

16mm

5 8

"

16mm

4X 1/4-20 UNC X 5/8"

CLOSER MOUNTING HOLES

2

3 4

"

70mm

3

3 4

"

95mm

CLOSER CUTOUT 

WIDTH

1 8

"

3mm

FROM FRAME EDGE IN

ALL CASES

5 8

"

16mm

MUST HAVE REMOVABLE STOP

1

3 4

"

44mm

MIN. FRAME WIDTH

7 16

"

11mm

FRAME RABBET TO

TAB MOUNT SURFACE

REMOVABLE STOP TABS IF NOT  USING FULL LENGTH REMOVABLE STOP

CLOSER MOUNTING TABS

 A 

19"

483mm

CUTOUT ON STOP SIDE ONLY

5 16

"

8mm

4

15 16

"

125mm

TOP OF DOOR

4"

102mm

MIN. WIDTH

1

5 8

"

41mm

CLOSER HEIGHT

1 8

"

3mm

FROM FRAME EDGE

IN ALL CASES

 A 

1

3 4

"

44mm

FRAME MIN.

OPTIONAL SPACER

REMOVABLE STOP

CLOSER

OPTIONAL RETRO  TRACK SPACER

NOTES:

MINIMUM STOP THICKNESS 1/2".
1.

1/8" DOOR TO SOFFIT CLEARANCE REQUIRED.
2.

REINFORCING PER ANSI/SDI-100 
3.

RECOMMENDED FOR HOLLOW METAL DOORS  & FRAMES. AUXILIARY STOP RECOMMENDED.

4.

HEADSTOP AND VERTICAL JAMB CUTOUT MUST 
5.

NOT EXCEED PIVOT TO JAMB CLEARANCE. DO NOT SCALE DRAWING.

6.

CONSULT FACTORY FOR DOOR THICKNESS 
7.

GREATER THAN 1-3/4".

LEFT HAND DOOR AND CLOSER SHOWN.  RIGHT HAND OPPOSITE.

A REMOVABLE HEADSTOP MUST BE USED IN COMBINATION  WITH THE CLOSER FOR PROPER INSTALLATION. MOUNTING HOLES FOR THE HEADSTOP MUST SPAN CLOSER LENGTH. HEADSTOP MUST BE  REMOVABLE TO INSTALL CLOSER AND MAKE PROPER ADJUSTMENTS.

C

PRODUCT:

TEMPLATE NUMBER:

DATE:

93 OHC CLOSER

OC60938

07/2021

MODEL 93 OVERHEAD CONCEALED CLOSER CENTER PIVOT, METAL FRAME 

MAX. DEGREE OF OPENING

93 NON HOLD OPEN (120

)

93 NON HOLD OPEN WITH TRACK STOP(120

93 HOLD OPEN (100

)

Copyright    2021 ASSA ABLOY Accessories and Door Controls Grou

p, Inc. All rights reserved. Reproduction in whole or in 

part without the express written permission of ASSA ABLOY Acces

sories and Door Controls Group, Inc. is prohibited.

www.rixson.com

"A" Dimension

Standard Appilcation

1" - 1/16" (27)

Retrofit Track Option

1" -  3/8" (35)

Model 93

 

Overhead Concealed Closer

 

Template

Center Pivot Hung 

Metal Frame

Содержание RIXON W93













Отзывы: