Assa Abloy Orion Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 55

background image

9

ASSA ABLOY Hospitality

66 8003 015-3

1.2 Terminology

Deadband

The range the temperature is allowed to drift before heating or
cooling is activated.

Default setpoint

Default setpoint

is the temperature which the thermostat is set to

until a guest changes the temperature. The thermostat will also
return to the

default setpoint

after guest check-out.

Dynamic setback

The

dynamic setback

temperatures are configured as

a set number of degrees above or below the guest setting.
For example, if the guest setting is 68 ºF (20 ºC) and the
unoccupied setback is configured to 7 ºF (4 ºC) above the
guest setting, the system will allow the temperature to drift
to 75 ºF (24 ºC) when the room is unoccupied.

EMS

Energy Management System

Exterior door
timeout

The time that will pass before the HVAC is turned off after
an exterior door is left open.

FCU

Fan Coil Unit

Freeze guard

If the temperature in any room with a thermostat goes
below 39 ºF (4 ºC), there will be an alarm and the HVAC
will start heating.

HVAC

Heating Ventilation and Air Conditioning

Intelligent switch

The intelligent switch is an output for lighting control which works
according to the occupancy status. The available alternatives for
intelligent switch are:

disabled; default
use RV output
use G2 output

If intelligent switch is applicable, normally 'Use RV output' should
be marked unless the air handler is a heat pump. In the latter
case, mark 'Use G2 output' instead.

Motion sensor

A device that detects a person's movement in an area.

Occupied

Someone is physically in the room; see section

Room occupied

for more information.

Occupied limits

Limits the

Set temperature

range, i.e. the temperature

which the guest can set the thermostat to.

PTAC
(Package Terminal
Air Conditioner)

A PTAC is a fully self contained system that is typically
located on the exterior wall of a hotel room. These units
come in standard control or heat pump models.

Pre-condition time

Note:

This

parameter
requires that the
Online option has
been set in
Visionline.

Number of hours the thermostat shall run at the

default

setpoint

after check-in. If no entry has been done when

this time expires, the unoccupied setback will be assumed.
The

pre- condition time

can be 1-12 hours or 'disabled';

default is 2 hours.

«
...
7
8
9
10
11
...
»

Содержание Orion
























































Отзывы:

Нет отзывов

Похожие инструкции для Orion

Бренд: RELSIB Страницы: 2

Бренд: RS PRO Страницы: 16

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 84

Бренд: Oregon Scientific Страницы: 15

Бренд: Peco Страницы: 1

Бренд: TUV Страницы: 5

Бренд: Digi-Sense Страницы: 8

Бренд: ThermoProbe Страницы: 7

Wi5 Wi-Fi Series

Бренд: Living Heat Страницы: 4

Бренд: OJ Electronics Страницы: 2

Бренд: Kobold Страницы: 18

Бренд: VDH Страницы: 4

Бренд: Fluke Страницы: 26

Бренд: Regulus Страницы: 4

Бренд: Mi-Heat Страницы: 8

Бренд: Aprilaire Страницы: 2

Бренд: Aprilaire Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды