AsReader ASR-020D Скачать руководство пользователя страница 26

Страница: 26 / 162

B-16

Trigger Modes

•

Level - A trigger event activates decode processing, which continues until the trigger

event ends, a valid decode, or the

Decode Session Timeout on page B-21

occurs.

•

Presentation Mode - When the decoder detects an object in its field of view, it triggers

and attempt to decode. The range of object detection does not vary under normal

lighting conditions. This applies to decode mode only. In this mode the unit does not

enter Low Power mode.

•

Auto Aim - This trigger mode turns on the aiming pattern when the decoder senses

motion. A trigger pull activates decode processing. After 2 seconds of inactivity the

aiming pattern automatically shuts off.

•

Auto Aim with Illumination - This trigger mode turns on the aiming pattern and

internal illumination LEDs when the decoder senses motion. A trigger pull activates

decode processing. After 2 seconds of inactivity the aiming pattern and internal

illumination LEDs automatically shut off.

Содержание ASR-020D



































































































































































Результаты поиска

Содержание ASR-020D

Отзывы:

AsReader ASR-020D, Руководство по параметрам, Страница: 26 / 162

Результаты поиска

Содержание ASR-020D

Отзывы: