AsReader ASR-020D Скачать руководство пользователя страница 22

Страница: 22 / 162

B-12

Illumination Brightness

This feature sets the brightness of the illumination by altering LED power. The default is 10,

which is maximum LED brightness. For values from 1 to 10, LED brightness varies from

lowest to highest level of brightness.

To program Illumination Brightness, scan this bar code followed by two numeric bar codes

Appendix Numeric Bar Codes

that correspond to the value of desired illumination

brightness. For example, to set Illumination Brightness to 6, scan the bar code below

followed by the 0 and 6 bar codes.

NOTE

This feature sets the brightness of the illumination by altering LED power. The allowed

range is from 1 to 27; LED brightness varies from lowest to highest level of brightness. The default is 7.

Using a brightness above 7 is not recommended, unless all thermal issues are considered.

Содержание ASR-020D



































































































































































Результаты поиска

Содержание ASR-020D

Отзывы:

AsReader ASR-020D, Руководство по параметрам, Страница: 22 / 162

Результаты поиска

Содержание ASR-020D

Отзывы: