Aspira AP20060 Скачать руководство пользователя страница 25

Страница: 25 / 28

E N G L I S H

ASPIRCOMFORT PRO dH

7 ALARMS

In case of any problems or failures, take note of any error code appearing on the remote control screen, take note

of the model and the serial number of the unit you possess (data provided on the identification plate attached on

the side of the unit) and contact the installer.

7.1 PROBLEMS WITHOUT ANY INDICATION OF THE ERROR ON THE DISPLAY

Problem

Causes

Solutions

Display off

No power supply

(luminous switch off)

Check the connection to the electrical

mains.

Poor or no air flow rate

The rooms remain humid

Clogged filters

Change the filters

Clogged exchanger

Clean the exchanger

Frozen exchanger

Take the exchanger to a warm place

and wait for it to defrost, do not heat

with direct sources of heat.

Dirty fan

Clean the fan

Clogged fan ducts

Clean the fan ducts

Outdoor temperature below 0 °C

The unit might be in anti-freeze mode,

wait until the outdoor temperature

rises or install an electric heater for

pre-heating.

High noise level

Noise generated by the unit

Check for cracks and/or air leaks from

the unit panels

Check the trap connection

Check whether the motors are spinning

correctly (bearings)

Noise coming from the ducts

Check for cracks on the suction / supply

/ exhaust ducts

Содержание AP20060





























Результаты поиска

Содержание AP20060

Отзывы:

Похожие инструкции для AP20060

Бренды по названию

Популярные бренды

Aspira AP20060, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AP20060

Отзывы:

Похожие инструкции для AP20060

Бренды по названию

Популярные бренды