ASM 249616 Скачать руководство пользователя страница 3

Specifications

311206A

3

Specifications

This equipment is not intended for use with flammable or combustible materials used in places
such as cabinet shops or other “factory” or fixed locations. If you intend to use this equipment in
this type of application, you must comply with NFPA 33 and OSHA requirements for the use of
flammable and combustible materials.

EQUIPMENT MISUSE HAZARD 

Misuse can cause death or serious injury.

Do not exceed the maximum working pressure or temperature rating of the lowest rated system 
component. See 

Technical Data

 in all equipment manuals.

Use fluids and solvents that are compatible with equipment wetted parts. See 

Technical Data 

in all

 

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information 
about your material, request MSDS from distributor or retailer. 

Check equipment daily. Repair or replace worn or damaged parts immediately with genuine ASM 
replacement parts only.

Do not alter or modify equipment.

For professional use only.

Use equipment only for its intended purpose. Call your ASM distributor for information.

Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

Do not kink or over bend hoses or use hoses to pull equipment.

Keep children and animals away from work area.

Do not operate the unit when fatigued or under the influence of drugs or alcohol.

Comply with all applicable safety regulations.

PRESSURIZED ALUMINUM PARTS HAZARD 

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids 
containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical 
reaction and equipment rupture, and result in death, serious injury, and property damage. 

CARBON MONOXIDE HAZARD

Exhaust contains poisonous carbon monoxide, which is colorless and odorless. Breathing carbon mon-
oxide can cause death. Do not operate in an enclosed area.

PERSONAL PROTECTIVE EQUIPMENT 

You must wear appropriate protective equipment when operating, servicing, or when in the operating 
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic 
fumes, burns, and hearing loss. This equipment includes but is not limited to:

Protective eyewear 

Clothing and respirator as recommended by the fluid and solvent manufacturer

Gloves

Hearing protection

WARNING

Содержание 249616

















Отзывы: