ASM 249166 Скачать руководство пользователя

Страница: 18 / 40

309508

Pressure Control Repair

Motor Control Board

Removal

Refer to Fig. 6.

Relieve pressure

;

page 9.

Remove four screws (18) and cover (39).

Disconnect at motor control board (35):

Four motor leads: two yellow, black (+) and
red (–).

Filter board motor leads, brown and blue.

Lead (D) from potentiometer.

Lead (E) from transducer.

Remove five screws (36), circuit board (35) and
filter board (40).

Installation

Clean pad on rear of motor control board. Apply
small amount of thermal compound to pad.

Fig. 5. Install motor control board (35) with four
screws (36). Install filter board (40) and secure
with fifth screw (36).

Connect to motor control board (35):

Lead (E) to transducer.

Lead (D) to potentiometer.

Four motor leads: two yellow, black (+) and
red (–).

Filter board leads, brown and blue.

Install cover (39) with four screws (18).

Motor Control Board Diagnostics

Note:

Keep a new transducer on hand to use for test.

CAUTION

Do not allow sprayer to develop fluid pressure with-
out transducer installed. Leave drain valve open if
test transducer is used.

Remove four screws (18) and cover (39).

Turn ON/OFF switch ON.

Observe LED operation and reference following
table:

Relieve pressure and unplug sprayer before ser-
vicing control board

;

page 9.

LED
BLINKS

SPRAYER OPERATION

INDICATES

WHAT TO DO

Once

Sprayer runs

Normal operation

Do nothing

Two times
repeatedly

Sprayer shuts down and LED continues
to blink two times repeatedly

Run away pressure. Pres-
sure greater than 4500 psi
(310 bar, 31 MPa).

Replace motor control board.
See preceding Motor control
board removal procedure.

Three times
repeatedly

Sprayer shuts down and LED continues
to blink three times repeatedly

Pressure transducer is
faulty or missing

Check transducer connection.
Open drain valve. Substitute
new transducer for transducer
in sprayer. If sprayer runs,
replace transducer.

Four times
repeatedly

Sprayer shuts down and LED continues
to blink four times repeatedly

Line voltage is too high

Check for voltage supply
problems

Five times
repeatedly

Sprayer shuts down and LED continues
to blink five times repeatedly

Too much current

Check for locked rotor,
shorted wiring or motor. Re-
pair or replace failed parts.

Содержание 249166









































Результаты поиска

Содержание 249166

Отзывы:

Похожие инструкции для 249166

Бренды по названию

Популярные бренды

ASM 249166, Инструкция по ремонту и список запасных частей

Результаты поиска

Содержание 249166

Отзывы:

Похожие инструкции для 249166

Бренды по названию

Популярные бренды