ASL INTERCOM PS 4379, Руководство пользователя

Страница: 13 / 22

DIP SWITCH BLOCK F
No. 6 STAGE ANNOUNCE MIC. SELECT
(factory setting = 'off')
This dip switch is only for use in EXTENDED mode
(See section 9 MODES). If the dip switch is in 'off'
position, the gooseneck or headset microphone and
the Stage Announce output of the master unit is
used. If the dip switch is in 'on' position, the micro
phone and stage Announce output of the unit is
used, of which the STAGE ANNOUNCE button is
pressed.
No. 5 SPEAKER DIM and STAGE ANNOUNCE
(factory setting = 'off')
In 'off' position the Speaker of the PS 4379 will not
reduce in volume when the STAGE ANNOUNCE
button is pressed. In 'on' position, the Speaker and
Program volume will be dimmed to zero as long as
the STAGE ANNOUNCE button is pressed.
No. 4 STAGE ANNOUNCE and AUXILIARY
(factory setting = 'off')
In 'off ' position, no aux signal will be sent to the
STAGE ANNOUNCE output. In 'on' position, the
Aux signal will be sent to the STAGE ANNOUNCE
output. When pressing and holding the STAGE
ANNOUNCE button, the AUX volume will be
dimmed to a set level. This dim factor is set by
pressing and holding the STAGE ANNOUNCE
button and turning the AUX level / IFB dim knob.
The set level will be shown on the AUX level / IFB
LED bar. The dim factor is stored by shortly
pressing the AUX level / IFB knob.
By first pressing the STAGE ANNOUNCE button,
releasing it and pressing and holding it again within
1 second, the AUX level LED bar will show the
volume setting of the Auxiliary. This can be then
adjusted by turning the AUX level / IFB Dim knob.
No. 3 RESERVED
No. 2 RESERVED
No. 1 MIC MUTE BLOCK
(factory setting = 'off')
When in SYSTEM LINK and the dip-switch is in 'off'
position the mic mute signals of the connected
intercom system will be routed to the outputs of the
PS 4379. If the dip-switch is in 'on ' position, the
Mic Mute signals of the connected intercom signals
will not be detected by the PS 4379 and not routed
to the outputs of the unit.
DIP SWITCH BLOCK C
No. 6 RESERVED (factory setting = 'off')
No. 5 RESERVED (factory setting = 'off')
No. 4 PAGING Channel D (factory setting = 'off')
If this dip switch is in 'on' position, the
corresponding channel will be set to PAGING
mode. (For PAGING functions see point 9.0
MODES)
No. 3 PAGING Channel C (factory setting = 'off')
(Same as for No. 4)
No. 2 PAGING Channel B (factory setting = 'off')
(Same as for No. 4)
No. 1 PAGING Channel A (factory setting = 'off')
(Same as for No. 4)
DIP SWITCH BLOCK D
No. 6 RESERVED (factory setting = 'off')
No. 5 RESERVED (factory setting = 'off')
No. 4 TALK MOMENTARY Channel D
(factory setting = 'off')
If this dip switch is in 'on' position, the
corresponding TALK button of that channel will be
set to momentary only.
No. 3 TALK MOMENTARY Channel C
(factory setting = 'off')
(Same as for No. 4)
No. 2 TALK MOMENTARY Channel B
(factory setting = 'off')
(Same as for No. 4)
No. 1 TALK MOMENTARY Channel A
(factory setting = 'off')
(Same as for No. 4)
DIP SWITCH BLOCK E
No. 6 RESERVED (factory setting = 'on')
No. 5 RESERVED (factory setting = 'on')
No. 4 IFB or AUX INPUT for IFB Channel D
(factory setting = 'on')
If this dip switch is switched off, the auxiliary of the
AUX input is routed to the IFB channel.
No. 3 IFB or AUX INPUT for IFB Channel C
(factory setting = 'on')
` (Same as for No. 4)
No. 2 IFB or AUX INPUT for IFB Channel B
(factory setting = 'on')
(Same as for No. 4)
No. 1 IFB or AUX INPUT for IFB Channel A
(factory setting = 'on')
(Same as for No. 4)
8.0 INTERNAL CONTROLS / DIP SWITCHES
User Manual PS 4379 - Issue 1 © 2007 ASL Intercom, Utrecht, The Netherlands 13