Ashida ADR141A Скачать руководство пользователя страница 77

Страница: 77 / 151

ADR141A /
ADR241A

Doc ID : ADR241A_IM_01
Ref ID : ADR241A/IM/SS
Rev No.

: 02

Page No. : 77 of 150

This setting is used to set the time-delay for Definite Time (C6) setting if selected for first stage ground
over current.

14.

IP>> Delay

0.05s

000 – 10.0s in steps of 0.01s

This setting is used to set the time-delay for second stage over current.

15.

IE>> Delay

0.05s

000 – 10.0s in steps of 0.01s

This setting is used to set the time-delay for second stage ground over current.

16.

BF Delay

50ms

000 – 800 msec.

This setting for the time-delay for the CBF trip.

17.

CT Secondary

1 A

1 A/5 A

This setting is used to set the CT Secondary

18.

CT Primary

10 A

10 – 5000A in step of 1A

This setting is used to set the CT Primary.

19.

Test Block

01 – 02 (1= Yes, 2= No)

This setting is used to enable (turn on) or disable (turn off) the CB Trip operation through relay HMI.

20.

Trip Circuit

01 – 02 (1= Yes, 2= No)

This setting is used to enable (turn on) or disable (turn off) Trip circuit supervision. This is used to
monitor trip coil which is used to trip the circuit breaker.

21.

Ann. Type

1 – 4

This setting is used select the annunciation type.

22.

Ann. Contact

01 –02 (1=SR, 2=HR)

This setting specifies to ann. contact can be set to Manual/Hand reset (HR) or Self reset (SR)

23.

Trip Contact

01 –02 (1=SR, 2=HR)

This setting specifies to Trip1 and Trip2 contact can be set to Manual/Hand reset (HR) or Self reset (SR)

24.

BF Contact

01 –02 (1=SR, 2=HR)

This setting specifies to BF contact can be set to Manual/Hand reset (HR) or Self reset (SR)

25.

Com Port

USB

USB/RS485

This setting specifies to select communication port for 103 communications.

26.

Set Parity

None

None/ Even/ Odd

This setting is used to set parity. It is important that both relay and master station are set with the same
parity setting.

27.

Baud Rate

57600

2400/ 4800/ 9600/ 14400/ 19200/ 28800/

38400/ 57600

This setting is used to set Baud rate It is important that both relay and master station are set with the
same Baud rate setting.

Содержание ADR141A
























































































































































Результаты поиска

Содержание ADR141A

Отзывы:

Ashida ADR141A, Инструкция по эксплуатации, Страница: 77 / 151

Результаты поиска

Содержание ADR141A

Отзывы: