Ashida ADR141A Скачать руководство пользователя страница 107

Страница: 107 / 151

ADR141A /
ADR241A

Doc ID : ADR241A_IM_01
Ref ID : ADR241A/IM/UG
Rev No.

: 02

Page No. : 107 of 150

BF Delay = 200

Range 000 – 800ms

Editable Setting

After tripping operation relay start this timing, if current does

not become zero during this time, relay declare as breaker

failure.

By using the Plus / Up arrow key (+ /

) or the Minus / Down

arrow key (- /

) the desired

BF Delay

can be set.

The range is from 000 to 800 ms in step of 50ms.

The 000

means bypass this feature.

Press the Left arrow key (

) to move to the next option.

CT Sec. = 001

1 = 1A, 2 = 5A

Editable Setting

By using the Plus / Up arrow key (+ /

) or the Minus / Down

arrow key (- /

) the desired

CT Secondary

can be set i.e. 1A /

5A. I.e.1 or 2. In which, 1 corresponds with 1 Amp. and 2

correspond with 5 Amp respectively.

Press the Left arrow key (

) to move to the next option.

CT Primary = 0100

Range 10 – 5000

Editable Setting

By using the Plus / Up arrow key (+ /

) or the Minus / Down

arrow key (- /

) the desired

CT Primary

can be set.

The Setting Range is from 10 to 5000A in steps of 1A. (For

example suppose CT Ratio is 500/1A then you have to select

CT Pri =500 so that when 1A current flows into relay circuit, in

measurement window it will show you 500A).

Press the Left arrow key (

) to move to the next option.

Test Block = 02

01= Yes, 02 = No

Editable Setting

This setting is use to Test block function. Normally Trip Test is

required during pre commission testing to check operation of

relay and panel wiring.

By using the Plus / Up arrow key (+ /

) or the Minus / Down

arrow key (- /

) the desired

Test Block

can be disable or

enable, i.e. 1 or 2. When the given set value is 2 then it will

enable Trip Test function, but when the given set value is 1

then Trip Test function will be blocked.

Press the Left arrow key (

) to move to the next option.

Содержание ADR141A
























































































































































Результаты поиска

Содержание ADR141A

Отзывы:

Ashida ADR141A, Инструкция по эксплуатации, Страница: 107 / 151

Результаты поиска

Содержание ADR141A

Отзывы: