Ashida ADR141A Скачать руководство пользователя страница 145

Страница: 145 / 151

Doc ID : ADR241A_IM_01

Ref ID : ADR241A/IM/TC

Rev No. : 02

Page No. : 145 of 150

ADR141A /
ADR241A

Step 6:

Start the PC terminal emulation software and establish communication with the

relay.

Step 7:

Set the correct relay time and date by using either the front panel or serial port

commands

Step 8:

Verify the relay ac connections.

Step 9:

Connect the ac test source current to the appropriate relay terminals. Disconnect

the current transformer secondary from the relay prior to applying test source

quantities.

Step 10:

Apply rated current (1 A or 5 A).

Step 11:

If the relay is equipped with voltage inputs, apply rated voltage for your

application.

11.3

Check Relay Setting

The relay setting check ensures that all of application specific relay setting for the particular

installation have been correctly applied to the relay. Enter all setting manually via the relay

front panel interface.

The commissioning of following points:

a. Ensure over current and earth fault trip setting.

b. Ensure TMS setting of over current and Earth Fault are entered correctly as per

required time grading between feeder and incomer.

c. Ensure instantaneous HF setting done correctly and its definite time delay is applied

properly as per required time grading between feeder and incomer.

d. Ensure selection of extra annunciation duty contacts is as per required function.

e. Ensure measure of applied current is same as the current measure in CT secondary

Final Check

After completion of all relay functionality testing and relay setting check. Remove all

temporary shorting leads etc. if it is necessary to disconnect any of the external wiring from

the relay in order to perform the wiring verification test. It should be ensured with the CT

connection are replaced in accordance with the relevant external connection or schemes

diagram. Ensure all fault & Annunciation contacts, trip contacts has been reset before

leaving relay.

If relay ADR141A/ ADR241A is a newly installed or the CB has been just maintained the trip

counter of Relay should be zero. This counter can be reset by applying Load Default Setting

(refer chapter number 8 User Guide to load default setting in relay)

Note: This will also clear all fault memory and the set password.

Содержание ADR141A
























































































































































Результаты поиска

Содержание ADR141A

Отзывы:

Ashida ADR141A, Инструкция по эксплуатации, Страница: 145 / 151

Результаты поиска

Содержание ADR141A

Отзывы: