Ascon tecnologic KX6 Series, Инструкция по эксплуатации

Страница: 24 / 28

Ascon Tecnologic - KX6 - ENGINEERING MANUAL - Vr. 0.0
PAG. 24
]
sp group - set point parameters
no. param. description
dec.
point
values default
60 nSP Number of used set points 0 1... 4 1
61 SPLL Minimum set point value dP From -1999 to SPHL -1999
62 SPHL Maximum set point value dP From SPLL to 9999 9999
63 SP Set point 1 dP From SPLL to SPLH 0
64 SP 2 Set point 2 dP From SPLL to SPLH 0
65 SP 3 Set point 3 dP From SPLL to SPLH 0
66 SP 4 Set point 4 dP From SPLL to SPLH 0
67 A.SP Selection of the active set point 0 From 1 (SP 1) to nSP 1
68 SP.rt Remote set point type 0
rSP = The value coming from serial link is used as remote SP;
trin = The value will be added to the local set point selected
by A.SP and the sum becomes the operative set point;
PErc = The value will be scaled on the input range and this
value will be used as remote SP.
trin
69 SPLr Local/remote set point selection 0
Loc = Local;
rEn = Remote.
Loc
70 SP.u
Rate of rise for positive set point
change (ramp UP)
2 0.01... 99.99 (inF) engineering units per minute inF
71 SP.d
Rate of rise for
negAtive
set point
change (ramp DOWN)
2 0.01... 99.99 (inF) engineering units per minute inF
]
pAn group - operator hmi parameters
no. param. description
dec.
point
values default
72 PAS2
Level 2 password (limited
access level)
0
- oFF (Level 2 not protected by password);
- 1... 200.
20
73 PAS3
Level 3 password (com-
plete configuration level)
0 3... 200 30
74 uSrb
button function during
RUN TIME
nonE = No function;
tunE = Auto-tune/self-tune enabling. A single press (longer than 1 se-
cond) starts the auto-tune;
oPLo = Manual mode. The first pressure puts the instrument in manual mode
(oPLo) while a second one puts the instrument in Auto mode;
AAc = Alarm reset;
ASi = Alarm acknowledge;
St.by = Stand by mode. The first press puts the instrument in stand by
mode while a second one puts the instrument in Auto modet;
SP1.2 = SP/SP2 selection.
tunE
75 diSP Middle display management
nonE = Standard display;
SPF = Final set point;
Spo = Operative set point;
AL1 = Alarm 1 threshold;
AL2 = Alarm 2 threshold;
Po = Power Output
0
76 di.cL Colour of the upper display
0 = The display colour is used to show the actual deviation (PV - SP);
1 = Display red;
2 = Display green;
3 = Display orange.
0
77 AdE
Deviation for display colour
management
1... 9999 (E.U.) 5
78 diS.t Display Timeout 2
- oFF (display always ON);
- 0.1... 99.59 (mm.ss).
oFF
79 fiLd
Filter on the displayed
value
1
- oFF (filter disabled);
- 1... 100 (E.U.).
oFF
80 dSPu
Instrument status at power
ON
AS.Pr = Starts in the same way it was prior to the power down;
Auto = Starts in Auto mode;
oP.0 = Starts in manual mode with a power output equal to zero;
St.bY = Starts in stand-by mode.
AS.Pr
81 oPr.E Operative modes enabling
ALL = All modes will be selectable by the next parameter;
Au.oP = Auto and manual (oPLo) mode only will be selectable by the next
parameter;
Au.Sb = Auto and Stand-by modes only will be selectable by the next parameter
ALL
82 oPEr Operative mode selection
If oPr.E = ALL: - Auto = Auto mode;
- oPLo = Manual mode;
- St.bY = Stand by mode;
If oPr.E = Au.oP: - Auto = Auto mode;
- oPLo = Manual mode;
If oPr.E = Au.Sb: - Auto = Auto mode;
- St.bY = Stand by mode.
Auto