Ascon tecnologic KX6 Series, Инструкция по эксплуатации

Страница: 23 / 28

Ascon Tecnologic - KX6 - ENGINEERING MANUAL - Vr. 0.0
PAG. 23
]
lbA group - loop break Alarm parameters
no. param. description
dec.
point
values default
35 LbAt LBA time 0 From 0 (oFF) to 9999 (s) oFF
36 LbSt Delta measure used by LBA during Soft start dP From 0 (oFF) to 9999 (E.U.) 10
37 LbAS Delta measure used by LBA dP 1...9999 (E.U.) 20
38 LbcA Condition for LBA enabling 0
uP = Active when Pout = 100%;
dn = Active when Pout = -100%;
both = Active in both cases.
both
]
reg group - Control parameters
no. param. description
dec.
point
values default
39 cont
Control type (when the controlled is
equipped with digital outputs)
Pid = PID (Single or double action);
On.FA = ON/OFF asymmetric (Single action);
On.FS = ON/OFF symmetric (Single action);
nr = ON/OFF double action with neutral zone;
3Pt = Servomotor control (Out 1 = open, Out 2 = close).
40 Auto Autotuning selection 0
-4 = Oscillating auto-tune with automatic restart at power up
and after all point change;
-3 = Oscillating auto-tune with manual start;
-2 = Oscillating -tune with automatic start at the first power up only;
-1 = Oscillating auto-tune with automatic restart at every power up;
0 = Not used;
1 = Fast auto tuning with automatic restart at every power up;
2 = Fast auto-tune with automatic start the first power up only;
3 = FAST auto-tune with manual start;
4 = FAST auto-tune with automatic restart at power up and after
a set point change;
5 = Evo-tune with automatic restart at every power up;
6 = Evo-tune with automatic start the first power up only;
7 = Evo-tune with manual start;
8 = Evo-tune with automatic restart at power up and after a set
point change.
7
41 tunE Manual start of the Autotuning 0
oFF = Not active;
on = Active
oFF
42 hSet Hysteresis of the ON/OFF control dP 0... 9999 (E.U.)
43 Pb Proportional band dP 1... 9999 (E.U.) 50
44 ti Integral time 0 From 0 (oFF) to 9999 (s) 200
45 td Derivative time 0 From 0 (oFF) to 9999 (s) 50
46 Fuoc Fuzzy overshoot control 2 0.00... 2.00 0.50
47 tch Heating output cycle time 1 0.1... 130.0 (s) 20.0
48 rcG
Power ratio between heating and
cooling action
2 0.01... 99.99 1.0
49 tcc Cooling output cycle time 1 0.1... 130.0 (s) 20.0
50 rS Manual reset (Integral pre-load) 1 -100.0... +100.0 (%) 0.0
51 Str.t Servomotor stroke time 0 5... 300 seconds 60
52 db.S Servomotor dead band 0 0...10.0% 50
53 oP.L Minimum Power Output From 100 to OP.H%
54 oP.H Maximum Power Output From OP.L to 100%
55
St.P
Maximum power output used during
soft start
0 -100... 100 (%) 0
56
SSt Soft start time 2
- 0.00 (oFF);
- 0.01... 7.59 (hh.mm);
- inF (always ON).
oFF
57
SS.tH Threshold for soft start disabling dP -1999... +9999 (E.U.) 9999
58 Pot Potentiometer enabling
nonE = Potentiometer not used;
Pot.o = Potentiometer used for indication only;
Pot.c = Potentiometer used for feedback control
59 P.caL Automatic potentiometer calibration
no = The automatic potentiometer calibration is disabled;
YES = The automatic potentiometer calibration is enabled.