background image

 

 

MST200 Installation Guide                                                                                                                                   

1

                       

Copyright 2005-2010 by Aruba Networks, USA.    All rights reserved.   

 
 

Statement of Conditions 

 

In the interest of improving internal design, operation function, and/or reliability, Aruba Networks 
reserves the right to make changes to products described in this document without notice. Aruba 
Networks does not assume any liability that may occur due to the use or application of the product(s) 
described herein. 

 

DISCLAIMER: LIMITATION OF LIABILITY 

1

Before installation, it’s strongly recommended and requested that users pay particular attention to the 

safety warnings in the sequentially detailed operation procedures within the manual. If there’s any 

uncertainty or incapability of solving problems, contact the company’s customer support center. Please 

DO NOT incur any risk or try to verify situations by yourself. Otherwise, any consequence caused by 

the attempt shall be completely due to the user himself. 

2

Please periodically check whether the installed MST200 is damaged, worn-out or poses any danger. 

Any actual proof, sign or phenomenon of the afore-mentioned situations should be brought to the 

attention of the company at point of sale. Please DO NOT attempt to repair the product or replace any 

component. Otherwise, for any consequence arising out of or relating to the users’ attempt repair the 

product, including but not limited to damages, disuse, short circuit, fire, bodily injury, etc., the company 

shall not be liable. 

3. Users shall purchase or use the company’s MST200 voluntarily. Users shall understand on their own 

initiative and abide voluntarily by policies, regulations or laws of their respective nation or local 

territories. The consequence arising out of or relating to any violation of the local laws or regulations by 

the user, shall be solely imputed to the user himself, and the company shall not be liable. 

4. The company disclaims any and all warranties and guarantees, express, implied or otherwise, arising, 

with respect to the MST200 products or services, including but not limited to the warranty of 

merchandisability, the warranty of fitness for a particular purpose, and any warranty of non-infringement 

of the intellectual property rights of any third party. Liability of the company for loss is limited to the total 

amount paid to the company by the customer during the previous calendar year. The company will have 

no obligation or liability, whether arising in contract (including Warranty), tort (including active, passive 

or imputed negligence, strict liability or product liability) or otherwise for any special, incidental, 

Содержание AirMesh MST200



















Отзывы: