manualshive.com logo in svg

Artistic License DMX512, Руководство пользователя

Поделиться
Скачать
Artistic License DMX512 Скачать руководство пользователя страница 88

[email protected]  Fax +44 (0)20 84 26 05 51 

 

88 

 

Redirect 

Control 

 
A further three input pins alter the operation of the Pan and Tilt 
motors: 
 

Pin State 

Function 

 

Off (+5V) 

Pan operates normally. 

Pan Invert 

On (GND) 

Pan movement relative to DMX 
channel level is inverted 

Off (+5V) 

Tilt operates normally. 

Tilt 
Invert 

On (GND) 

Tilt movement relative to DMX 
channel level is inverted 

Off (+5V) 

Pan and Tilt operate as 
described above. 

Pan / Tilt 
Swap 

On (GND) 

Pan and Tilt motors are 
swapped. 

 
 

Pan Axis 

 
The Pan motor is driven in high resolution micro-stepping mode. In 
order to cater for variations in final product design, four different 
ranges of total travel are available. 
The travel settings are selected by PanSel1 & PanSel2. These pins 
are intended to be set at design time. They are not user controls. 
The pan axis calibrates by driving the motor into a mechanical limit. 
It is important to ensure that the mechanical stop is set to coincide 
with one of the natural steps of the motor. This will ensure that the 
calibration phase provides maximum accuracy. 
 

PanSel2 PanSel1  Travel 
0 0  360 

degrees 

0 1  240 

degrees 

1 0  180 

degrees 

1 1  120 

degrees 

 

Tilt Axis 

 
The Tilt motor is driven in high resolution micro-stepping mode. In 
order to cater for variations in final product design, four different 
ranges of total travel are available. 
The travel settings are selected by TiltSel1 & Tilt2. These pins are 
intended to be set at design time. They are not user controls. 
The tilt axis calibrates by driving the motor into a mechanical limit. 
It is important to ensure that the mechanical stop is set to coincide 
with one of the natural steps of the motor. This will ensure that the 
calibration phase provides maximum accuracy. 
 

TiltSel2 TiltSel1  Travel 
0 0  360 

degrees 

0 1  240 

degrees 

1 0  180 

degrees 

1 1  120 

degrees 

 

Содержание DMX512













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды