manualshive.com logo in svg

Artistic License DMX512, Руководство пользователя

Поделиться
Скачать
Artistic License DMX512 Скачать руководство пользователя страница 48

[email protected]  Fax +44 (0)20 84 26 05 51 

 

48 

 

Circuit 

Operation

 

 
The AL4008 provides chip selects and a data bus which is used to 
address a single switched output from the 24 available.  
The output devices used are 74HCT374 octal latches. 
Please not the 470R pull down network attached to the data bus. 
This device ensures that the relays do not momentarily energise 
during the power on sequence. 
 

DMX512 

Base 

Address 

 
The BCD inputs are used to set the DMX base address. The inputs 
are set up for connection of three standard Binary Coded Decimal 
Thumbwheel switches. The BCD inputs are active low, i.e. to select a 
base address of 001, connect UNIT1 to ground and pull up all other 
BCD inputs. Valid addresses range from 001 to 512. 
 

Test Mode 

 
The BCD inputs are also used to enter test mode. 
When Test mode is active, the DMX512 input is disabled. 
When the Hundred inputs are set to ‘7’ Test mode is active. The Ten 
and Units inputs select the channel. 
The following examples show the operation: 

 

Hundreds Tens Units Output 

DMX 
Input 

0 0 

0 

All 

Off 

Off 

0 

0 

1 

Controlled by inputs 

On 

5 

1 

2 

Controlled by inputs 

On 

7 

0 

1 

Output 1 On 

Off 

6 

1 

9 

Output 19 On 

Off 

 

DMX512 

Input 

 
The DMX512 input connects directly to the output of a standard 
RS485 or RS422 receiver such as the 75176. 
 

Good Data 

 
The GOOD signal is driven low to show that valid DMX512 data is 
being received. The output is suitable for direct connection (via a 
current limit resistor) to the cathode of a 20mA LED. 
 

Power 

Supply 

 
The AL4008 requires a 5V DC supply at approximately 6mA 
All Ground and Vcc pins must be connected. 
The device is CMOS so normal handling precautions should be 
adhered to. 
Good decoupling and pcb layout conventions (i.e. fill all unused pcb 
areas with grounded copper planes) should be followed. 
Particular attention should be paid to routing the crystal 
connections. 
 

Crystal 

 
The AL4008 requires a 16MHz, fundamental mode crystal. A tuning 
capacitance of approximately 12pF is suggested between each crystal 

Содержание DMX512













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды