manualshive.com logo in svg

Artistic License DMX512, Руководство пользователя

Поделиться
Скачать
Artistic License DMX512 Скачать руководство пользователя страница 11

[email protected]  Fax +44 (0)20 84 26 05 51 

 

11 

 

Phase 

Outputs

 

 
The AL4002 phase outputs are synchronised to the three zero cross 
input signals over a frequency range of 45 to 65Hz. The output phase 
trigger position is defined by the highest value of the DMX512 input, 
the analogue input and the preheat level. The output is additionally 
modified by the output curve selected. 
 

Phase 

Sequence 

 
The AL4002 is designed such that it can be used for both standard 
configurations of three phase dimmer. The two conventions differ in 
the sequence of the phase outputs and is selected by tying the 
ORDER pin either Hi or Low: 
 
DMX, Analogue or 
Test Input Channel 

Consecutive 
(ORDER=0) 
Controlled Output 

Alternate   
(ORDER=1) 
Controlled Output 

1 PH1-1 PH1-1 

2 PH1-2  PH2-1 
3 PH1-3  PH3-1 
4 PH1-4  PH1-2 
5 PH2-1 PH2-2 
6 PH2-2 PH3-2 
7 PH2-3  PH1-3 
8 PH2-4 PH2-3 
9 PH3-1 PH3-3 

10 PH3-2 PH1-4 

11 PH3-3 PH2-4 

 

12 PH3-4 PH3-4 

 

 

Dimmer 

Curves 

 
The phase output relationship to the control input can be globally 
modified to one of four response curves. The options are: 
1.

 

Linear - The output phase varies linearly with the input. 

2.

 

Square - The output power varies linearly with the input. 

3.

 

S curve - A modified form of Square with greater control in the 
centre of the range. 

4.

 

Relay - The output switches to full when the input exceeds 25%. 

The curves are selected as follows: 
 

 

CURVE1 

0 
0 
1 
1

 

CURVE0 

0 
1 
0 
1

 

Output 

Linear 
Square 
S Curve 
Relay

 

 

 
 

Zero Cross 

Inputs 

 
The three zero cross inputs (ZC1-3) are used to provide the mains 
synchronisation. The inputs are active low, that is the signal should 
pulls low at the zero crossing point of each respective phase. 
For single phase operation the three inputs should be commoned. 

Содержание DMX512













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды