manualshive.com logo in svg

Artistic License DMX512, Руководство пользователя

Поделиться
Скачать
Artistic License DMX512 Скачать руководство пользователя страница 13

[email protected]  Fax +44 (0)20 84 26 05 51 

 

13 

0 

0 

0 

Input 1 

Input 5 Input 9 

Spare 1 

0 

1 

Input 2 

Input 6 Input 10  Spare 2 

1 

0 

Input 3 

Input 7 Input 11 

Spare 3 

1 

1 

Input 4 

Input 8 Input 12  Preheat 

 

DMX512 

Input 

 
The DMX512 input connects directly to the output of a standard 
RS485 or RS422 receiver such as the 75176. 
 

Good Data 

 
The GOOD signal is driven low to show that valid DMX512 data is 
being received. The output is suitable for direct connection (via a 
current limit resistor) to the cathode of a 20mA LED. 
 

Fan Speed 

 
The HIFAN signal is driven Hi when any six outputs exceed 50% 
power. The signal can be used to increase the fan speed when the 
Dimmer is handling greater than 50% power. 
 

Power 

Supply 

 
The AL4002 requires a 5V DC supply at approximately 6mA 
All Ground and Vcc pins must be connected. 
The device is CMOS so normal handling precautions should be 
adhered to. 
Good decoupling and pcb layout conventions (i.e. fill all unused pcb 
areas with grounded copper planes) should be followed. 
Particular attention should be paid to routing the Zero Cross and 
Crystal connections. 
 

Crystal 

 
The AL4002 requires a 16MHz, fundamental mode crystal. A tuning 
capacitance of approximately 12pF is suggested between each crystal 
connection and Ground. The inherent pcb and lead capacitance must 
be included in this. 
 

EMC 

 
There are two major considerations in reducing the electromagnetic 
radiation generated by the AL4002. 
The device tends to generate noise at the third harmonic of the 
crystal (48MHz). Adding the crystal capacitors detailed above 
reduces this to acceptable limits. 
Broad band noise can be reduced by good decoupling. A range of 
22uF aluminium capacitors and 0u1 ceramic capacitors should be used 
on the circuit board. A 560pF ceramic capacitor should also be 
connected across the AL4002 power pins as close as possible to the 
device. 
The use of 150uH inductors in series with all three DMX512 signals 
is also an effective way to reduce conducted emissions. 
 

DMX512 

Isolation 

 
In order to ensure that DMX512 works reliably (this relates to all 

Содержание DMX512













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды