Artesyn MITX-CORE-820 Скачать руководство пользователя страница 106

Страница: 106 / 133

Firmware

MITX-CORE-820 Installation and Use (6806800M10H)

105

6.2.4

Standard Logical Device Configuration Register

All the standard logical device configuration registers can be accessed by the host processor
after reset. All registers are read/write enabled. The following table shows the detailed
definition of standard logical device configuration registers.

Table 6-2 Standard Configuration Register Map

Index

Description

07h

Logical Device Number

This register selects the current logical device
number.

20h

Super I/O ID

Super I/O configuration register and ID
registers

21h

Super I/O Configuration 1

24h

Super I/O Chip Revision

25h

Super I/O Configuration 5

26h

Super I/O Configuration 6

27h

Super I/O Revision ID

28h

Super I/O General Purpose Scratch

29h

Super I/O Configuration 9

2Dh

Super I/O Configuration D

2Eh - 2Fh

Reserved for Nuvoton use

30h

Logical Device Control (Activate)

Enable or disable the logical device

60h - 61h

IO Base Address Descriptor 0

Indicates selected I/O lower limit address

62h - 63h

IO Base Address Descriptor 1

70h

Interrupt Number

Indicates selected interrupt number

71h

IRQ Type Select

Indicates the type and polarity of the interrupt
request number selected in 70h

74h

DMA Channel Select 0

Indicates selected DMA channel for DMA 0 or
DMA 1 of the logical device.

75h

DMA Channel Select 1

F0h - FFh

Device Specific Logical Device
Configuration

Special (vendor-defined) configuration
options.

Содержание MITX-CORE-820






































































































































Результаты поиска

Содержание MITX-CORE-820

Отзывы:

Artesyn MITX-CORE-820, Инструкция по установке и эксплуатации, Страница: 106 / 133

Результаты поиска

Содержание MITX-CORE-820

Отзывы: