Arrow GA5M-A, Руководство пользователя и инструкция по сборке

Страница: 8 / 9

14
14J
Roof Assembly Chart
10’x10’
(3,0 m x 3,1 m)
10’x15’
(3,0 m x 4,6 m)
10’x20’
(3,0 m x 6,1 m)
10’x25’
(3,0 m x 7,5 m)
10’x30’
(3,0 m x 9,0 m)
EP RP RP RP RP EP
EP RP RP RP RP EP
RC - F/R RC - F/R
EP RP RP RP RP EP
EP RP RP RP RP EP
RP RP
RP RP
RC - F/R RC - MID RC - F/R
EP RP RP RP RP EP
EP RP RP RP RP EP
RP RP
RP RP
RP RP
RP RP
RC - F/R RC - F/R RC - MID RC - MID
EP RP RP RP RP EP
EP RP RP RP RP EP
RP RP
RP RP
RP RP
RP RP
RP RP
RP RP
RC - F/R RC - F/R RC - MID RC - MID RC - MID
EP RP RP RP RP EP
EP RP RP RP RP EP
RP RP
RP RP
RP RP
RP RP
RP RP
RP RP
RP RP
RP RP
RC - F/R RC - F/R RC - MID RC - MID RC - MID RC - MID
EP = End Panel (8578 / 8579)
RP = Roof Panel (7743)
RC - F/R = Front and Rear Ridge Cap (10621)
RC - MID = Mid Ridge Cap (10680)
No Extension
Modules.
1 Extension
Module.
2 Extension
Modules.
3 Extension
Modules.
4 Extension
Modules.
FRONT REAR
L = Left Roof Trim (80017)
R = Right Roof Trim (10620)
M = Mid Roof Trim (6015)
= Strip of Tape L R
L R
L R M
L R M
L R M
L R M
L R M
L R M
L R M
L R M
M
M
M
M
M
M
M
M
M
M
M
M
IMPORTANT: The symbol indicates a 2”
(5,1 cm) strip of Weather Stripping Tape. Cut
two strips of tape as well as two additional
strips for each Extension Module you are
installing and set aside for later use.
= 4
= 6
= 8
= 10
= 12
15
Working with one Truss Section at a time:
A)
Attach one end of the Mid Ridge Cap to the Front Ridge Cap
with two Bolts and Nuts.
B) Install four Roof Panels.
C) Seal the ridge of the building with Weather Stripping.
D)
Where Panels overlap under the Ridge Cap, secure with Bolts
and Nuts and seal with a strip of tape (see page 14).
Repeat these steps for additional Modules.
Step 8 - Install Roof Panels and Trim.
You will need the following parts for this step:
7743 Roof Panel 10680 Mid Ridge Cap
Step 8 continues on back page.
FASTEN TO WALL ANGLES LAST
FASTEN TO NEXT PANEL WITH BOLT AND NUT
FASTEN TO RIDGE CAP WITH BOLTS AND NUTS
FASTEN TO ROOF BEAMS WITH SCREWS
Use the diagram to the left when attaching Roof Panels.
• Secure the top row to Roof Beams
• Secure the middle row to Roof Beams
• Secure the lower row to Side Wall Angles
after all Panels have been installed.
Use washers on all fasteners
used on painted parts.
7743
15J
You will need to ‘roll’ the Panels
to secure the ribs together, just
as on Wall Panels (see page 12).
B
C
D
A
B
B
B
IMPORTANT: Apply Weather Stripping Tape after each
additional Panel is installed. A strip of Weather Stripping
Tape 2” (5,1 cm) long should be applied over each Bolt
that is under the Ridge Cap.