background image

* Size rounded off to the nearest foot

BUILDING DIMENSIONS

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.

708871204

Model No.

GD106-A

GDF106

697.68617

VD106-A
VR106-A

Owner's Manual & Assembly Instructions

       X1

                                                                       Exterior Dimensions             Interior Dimensions             Door

       *Approx.       Foundation        Storage Area           (Roof Edge to Roof Edge)              (Wall to Wall)               Opening
           Size               Size             Sq. Ft.  Cu. Ft.        Width      Depth      Height      Width     Depth    Height   Width  Height

         10' x 6'     121" x 68 3/4"           54        345        123 1/4"    71 1/4"     82 1/8"     118 1/4"      66"      80 7/8"   55 1/2" 69 1/4"

3,0m x 1,7m  307cm x 175cm        5,0m

2

      9,8m

3

       313cm       181cm       209cm        300cm      168cm     205cm    141cm   176cm

Содержание 697.68617

































Отзывы: