Armitage Shanks Sensorflow A4126AA Скачать руководство пользователя страница 9

Страница: 9 / 20

INSTALLATION GUIDE continued…

24 & 25

Connection of this product to mains

power supply should be undertaken by

a competent person and should conform

to IEE Wiring Regulations

Orientation & position of solenoids, and PSU

(

ower

upply

nit) case can differ from in

stallation to installation.

With the product securely mounted to the

panel & plumbed-in, electrical work can com-

mence.

12.

Locate the end of the red & black cable

which emerges from the spout (attached to

the rear of

the sensor). This cable length is nominal

750mm.

Connect the cable to the solenoid valve termi-

nals as shown. Observe the + and – symbols

marked on the solenoid valves, connect the

red cable to + & black to -.

Refer to the diagram on the next page for PSU

connection options.

red

black

Power:

Approval EU:

EN 60950, EN 60335

Approval UL:

UL 1310

Input voltage:

100V - 240V~ 50 - 60Hz

Protection class:

DIN EN 60730-1: Type 1

Each type of PSU is

identified by this

coloured dot system:

RED

DOT

BLUE

DOT

GREEN

DOT

MAINS

LINK

BATTERY

Electrical information

& approvals:

5.3

Electrical connection

Содержание Sensorflow A4126AA





















Результаты поиска

Содержание Sensorflow A4126AA

Отзывы:

Похожие инструкции для Sensorflow A4126AA

Бренды по названию

Популярные бренды

Armitage Shanks Sensorflow A4126AA, Руководство по установке

Результаты поиска

Содержание Sensorflow A4126AA

Отзывы:

Похожие инструкции для Sensorflow A4126AA

Бренды по названию

Популярные бренды