Armitage Shanks Sensorflow A4126AA Скачать руководство пользователя страница 7

Страница: 7 / 20

5.2

Plumbing Overview

Once the spout has been secured to the panel,

consideration should be given to installing &

positioning of the inline valves.

A typical plumbing installation example is

shown here. The water is being supplied from

below, but can be from any direction.

Short lengths of Ø15mm copper pipe

(not supplied) have been used between the

components. Copper pipe lengths should be

cut to suit the installation.

Note the Ø10mm inlet pipe (fitted to spout) can

be trimmed if necessary.

Observe arrow markings on the

valves as shown here. Ensure water

flows in the direction indicated.

4. To fit inlet elbow:

Slip the small compres-

sion nut & olive onto the Ø10mm inlet pipe.

Push the elbow onto the inlet pipe up to the

shoulder. Slide the olive up to the elbow &

tighten the compression nut (19mm A/F) with

a spanner. Hold the elbow steady with suit-

able grips.

ENSURE INLET PIPE REMAINS SECURELY

SCREWED INTO SPOUT.

INSTALLATION GUIDE continued…

Copper supply

pipe Ø 15mm

Short copper

pipe Ø 15mm

Short copper

pipe Ø 15mm

Spout inlet

pipe Ø 10mm

Inlet elbow

15 to 10mm

compression

Inline service

valve with filter

Inline

solenoid

valve

Filter

cap

Isolation

screw

2x Couplers

G1/2” female

thread to

15mm

compression

FLOW

DIRN

FLOW

DIRN

19 & 24

Содержание Sensorflow A4126AA





















Результаты поиска

Содержание Sensorflow A4126AA

Отзывы:

Похожие инструкции для Sensorflow A4126AA

Бренды по названию

Популярные бренды

Armitage Shanks Sensorflow A4126AA, Руководство по установке

Результаты поиска

Содержание Sensorflow A4126AA

Отзывы:

Похожие инструкции для Sensorflow A4126AA

Бренды по названию

Популярные бренды