ARM ARM9TDMI Скачать руководство пользователя

Страница: 97 / 154

Debug Support

ARM DDI0145B

5-43

Table 5-6 Watchpoint control register for instruction comparison bit functions

Bit

Function

ITBIT

Compares against the Thumb state signal from the core to determine between a
Thumb (

ITBIT

= 1) instruction fetch or an ARM (

ITBIT

= 0) fetch.

InTRANS

Compares against the not translate signal from the core in order to determine
between a user mode (

InTRANS

= 0) instruction fetch, and a privileged mode

(

InTRANS

= 1) fetch.

EXTERN

Is an external input into the EmbeddedICE macrocell that allows the watchpoint
to be dependent upon some external condition. The

EXTERN

input for

watchpoint 0 is labelled

EXTERN0

, and the

EXTERN

input for watchpoint 1

is labelled

EXTERN1

CHAIN

Can be connected to chain output of another watchpoint in order to implement,
for example, debugger requests of the form “breakpoint on address YYY only
when in process XXX”.

In the ARM9TDMI EmbeddedICE macrocell, the

CHAINOUT

output of

watchpoint 1 is connected to the

CHAIN

input of watchpoint 0. The

CHAINOUT

output is derived from a latch. The address/control field

comparator drives the write enable for the latch, and the input to the latch is the
value of the data field comparator. The

CHAINOUT

latch is cleared when the

control value register is written, or when

nTRST

is LOW.

RANGE

Can be connected to the range output of another watchpoint register. In the
ARM9TDMI EmbeddedICE macrocell, the

RANGEOUT

output of watchpoint

1 is connected to the

RANGE

input of watchpoint 0. This allows two

watchpoints to be coupled for detecting conditions that occur simultaneously, for
example, for range-checking.

ENABLE

If a watchpoint match occurs, the internal

Breakpoint

signal will only be

asserted when the ENABLE bit is set. This bit only exists in the value register, it
cannot be masked.

Содержание ARM9TDMI












































































































































Результаты поиска

Содержание ARM9TDMI

Отзывы:

Похожие инструкции для ARM9TDMI

Бренды по названию

Популярные бренды

ARM ARM9TDMI, Техническое справочное руководство

Результаты поиска

Содержание ARM9TDMI

Отзывы:

Похожие инструкции для ARM9TDMI

Бренды по названию

Популярные бренды