ARM ARM926EJ-S Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 248

background image

Programmer’s Model

ARM DDI0198D

Copyright © 2001-2003 ARM Limited. All rights reserved.

2-31

If either the data or instruction TCM is disabled, then the contents of the respective
TCM are not accessed. If the TCM is subsequently re-enabled, the contents will not
have been changed by the ARM926EJ-S processor.

For a Harvard arrangement, the instruction-side TCM must be accessible for both reads
and writes during normal operation, and for loading code, or for debug activity. This
enables accesses to literal pools, undefined instruction emulation, and parameter
passing for SWI operations. You must insert an

Instruction Memory Barrier

(IMB)

between a write to the instruction TCM and the instructions being read from the
instruction TCM. See Chapter 9

Instruction Memory Barrier

for more details.

Note

Instruction fetches from the data TCM are not possible. An attempt to fetch an
instruction from an address in the data TCM space does not result in an access to the
data TCM, and the instruction is fetched from main memory. These accesses can result
in external aborts, because the address range might not be supported in main memory.

The instruction TCM must not be programmed to the same base address as the data
TCM. If the two TCMs are of different sizes, the regions in physical memory must not
overlap. If they do overlap, it is Unpredictable which memory is accessed.

Note

The base address value setting must be aligned to the TCM size.

64KB

b0111

128KB

b1000

256KB

b1001

512KB

b1010

1MB

b1011

Reserved

b1100, b1101,
b1110, b1111

Table 2-24 TCM Size field encoding (continued)

Memory
size

Value

«
...
57
58
59
60
61
...
»

Содержание ARM926EJ-S

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM926EJ-S

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: Udoo Страницы: 7

Бренд: Fostex Страницы: 20

Бренд: IBA Страницы: 33

Бренд: Neo Instruments Страницы: 2

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Storage Networking (Unified Fabric Pilot)

Бренд: Qlogic Страницы: 76

Бренд: Tait Страницы: 8

Бренд: C4i Страницы: 5

Бренд: Teridian Страницы: 2

Бренд: Intel Страницы: 20

Бренд: Z3 Technology Страницы: 22

6026 Lapbank 16 mini

Бренд: Loxit Страницы: 2

ROADRECORDER 8400 NVR

Бренд: Safety Vision Страницы: 27

Бренд: JOBO Страницы: 12

Бренд: Atmel Страницы: 123

Бренд: Jabra Страницы: 2

Бренд: Vivotek Страницы: 185

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды