ARM ARM926EJ-S Скачать руководство пользователя страница 4

Страница: 4 / 248

Contents

ARM DDI0198D

Chapter 4

Caches and Write Buffer

4.1

About the caches and write buffer .............................................................. 4-2

4.2

Write buffer ................................................................................................. 4-4

4.3

Enabling the caches ................................................................................... 4-5

4.4

TCM and cache access priorities ............................................................... 4-8

4.5

Cache MVA and Set/Way formats .............................................................. 4-9

Chapter 5

Tightly-Coupled Memory Interface

5.1

About the tightly-coupled memory interface ............................................... 5-2

5.2

TCM interface signals ................................................................................. 5-4

5.3

TCM interface bus cycle types and timing .................................................. 5-8

5.4

TCM programmer’s model ........................................................................ 5-19

5.5

TCM interface examples ........................................................................... 5-20

5.6

TCM access penalties .............................................................................. 5-29

5.7

TCM write buffer ....................................................................................... 5-30

5.8

Using synchronous SRAM as TCM memory ............................................ 5-31

5.9

TCM clock gating ...................................................................................... 5-32

Chapter 6

Bus Interface Unit

6.1

About the bus interface unit ........................................................................ 6-2

6.2

Supported AHB transfers ............................................................................ 6-3

Chapter 7

Noncachable Instruction Fetches

7.1

About noncachable instruction fetches ....................................................... 7-2

Chapter 8

Coprocessor Interface

8.1

About the ARM926EJ-S external coprocessor interface ............................ 8-2

8.2

LDC/STC .................................................................................................... 8-4

8.3

MCR/MRC .................................................................................................. 8-6

8.4

CDP ............................................................................................................ 8-8

8.5

Privileged instructions ................................................................................. 8-9

8.6

Busy-waiting and interrupts ...................................................................... 8-10

8.7

CPBURST ................................................................................................ 8-11

8.8

CPABORT ................................................................................................ 8-12

8.9

nCPINSTRVALID ..................................................................................... 8-13

8.10

Connecting multiple external coprocessors .............................................. 8-14

Chapter 9

Instruction Memory Barrier

9.1

About the instruction memory barrier operation ......................................... 9-2

9.2

IMB operation ............................................................................................. 9-3

9.3

Example IMB sequences ............................................................................ 9-5

Chapter 10

Embedded Trace Macrocell Support

10.1

About Embedded Trace Macrocell support .............................................. 10-2

Содержание ARM926EJ-S











































































































































































































































Результаты поиска

Содержание ARM926EJ-S

Отзывы:

Похожие инструкции для ARM926EJ-S

Бренды по названию

Популярные бренды

ARM ARM926EJ-S, Техническое справочное руководство

Результаты поиска

Содержание ARM926EJ-S

Отзывы:

Похожие инструкции для ARM926EJ-S

Бренды по названию

Популярные бренды