ARM ARM926EJ-S Скачать руководство пользователя страница 239 | Manualshive

Страница: 239 / 248

background image

Glossary

ARM DDI0198D

Copyright © 2001-2003 ARM Limited. All rights reserved.

Glossary-15

Processor

A processor is the circuitry in a computer system required to process data using the
computer instructions. It is an abbreviation of microprocessor. A clock source, power
supplies, and main memory are also required to create a minimum complete working
computer system.

Physical Address (PA)

The MMU performs a translation on

Modified Virtual Addresses

(MVA) to produce the

Physical Address

(PA) which is given to AHB to perform an external access. The PA is

also stored in the data cache to avoid the necessity for address translation when data is
cast out of the cache.

See also

Fast Context Switch Extension.

Read

Reads are defined as memory operations that have the semantics of a load. That is, the
ARM instructions LDM, LDRD, LDC, LDR, LDRT, LDRSH, LDRH, LDRSB, LDRB,
LDRBT, LDREX, RFE, STREX, SWP, and SWPB, and the Thumb instructions LDM,
LDR, LDRSH, LDRH, LDRSB, LDRB, and POP. Java instructions that are accelerated
by hardware can cause a number of reads to occur, according to the state of the Java
stack and the implementation of the Java hardware acceleration.

RealView ICE

A system for debugging embedded processor cores using a JTAG interface.

Region

A partition of instruction or data memory space.

Remapping

Changing the address of physical memory or devices after the application has started
executing. This is typically done to allow RAM to replace ROM when the initialization
has been completed.

Reserved

A field in a control register or instruction format is reserved if the field is to be defined
by the implementation, or produces Unpredictable results if the contents of the field are
not zero. These fields are reserved for use in future extensions of the architecture or are
implementation-specific. All reserved bits not used by the implementation must be
written as 0 and read as 0.

Saved Program Status Register (SPSR)

The register that holds the CPSR of the task immediately before the exception occurred
that caused the switch to the current mode.

SBO

See

Should Be One.

SBZ

See

Should Be Zero.

SBZP

See

Should Be Zero or Preserved.

«
...
237
238
239
240
241
...
»

Содержание ARM926EJ-S

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM926EJ-S

Бренд: LORD Страницы: 9

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 8

FireWire 800 + Hi-Speed USB Combo

Бренд: SIIG Страницы: 20

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

Бренд: Daedalon Страницы: 6

Thin Client US310e

Бренд: NEC Страницы: 6

LBON320AC Series

Бренд: Lindsay Broadband Страницы: 4

Бренд: Grundig Страницы: 24

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

Бренд: Cameo Страницы: 23

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

Бренд: SeaLevel Страницы: 34

CNPS11X Extreme

Бренд: ZALMAN Страницы: 12

cPCIS-1100 Series

Бренд: ADLINK Technology Страницы: 48

Бренд: V-Count Страницы: 2

DataFire GO! PRO

Бренд: Digi Страницы: 20

AdvancedTCA AT8901M

Бренд: Kontron Страницы: 76

Бренд: A.E.B. Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды