Aritech ATS 500A Series, Инструкция по установке, Страница: 13 / 18

P/N 466-
5570 (EN) • REV E • ISS 22MAR22
13 / 18
It is required to apply the following supervision settings for
wireless DGPs:
•
Short supervision: 20 minutes
•
Long supervision: 2 hours
•
Smoke supervision: 4 hours
Refer to appropriate sections and manuals.
Caution: When any option, any additional function or any
additional zone type in this section does not comply with the
EN 50131 requirements, the EN 50131 Grade 2 label must be
removed from the system.
Additional functions
The Wireless PIR Camera functionality brings along video
verification feature, this additional function is fully available
without compromise to standards the system complies to.
The Wireless PIR camera system consists of the following:
•
Advisor Advanced series control panel
•
ATS1238 Advanced Wireless DGP
•
TX-2344-03-1 Wireless PIR Camera
•
ATS73X0 GSM/GPRS Module
These PIR camera settings have no influence on EN 50131
compliance:
•
2.2.2.n.4.9.1.1.2 Frame rate for all event types
•
2.2.2.n.4.9.1.1.3 Pic resolution for all event types
•
2.2.2.n.4.9.3 Pic auto deletion
•
4.5 Cameras
•
9.1.n.4.5 Pic dest port
•
9.3.n.11 Max Pics 24h, 9.3.n.7.9 Max Pics 24h
EN 50131 Grade 3
The following options and values are mandatory for EN 50131-
1 Grade 3 regulations:
•
All Grade 2
required settings (see “EN 50131 Grade 2” on
page 12).
•
PIN length should be 6 digits minimum.
•
3.2.n.6 User group options, set (6) Isolate, (22) SMS
reporting, (23) SMS control to No for all user groups
except Installer.
•
4.1.n.6.7 Anti mask, set to Yes for all I&HAS movement
detectors
•
4.2.n.2.1 Exit time 1
, ≤ 180 s
•
8.1.3.4 Mains reporting delay
, ≤ 1 h
•
8.3.5 View EE timer, set to Off
•
8.4.1 RTS options, set Zone masking condition to Yes
•
8.4.2 Inhibit includes, set Zone masking condition to
Access Level 2
•
Battery test should be performed daily.
The following features are not allowed (not evaluated):
•
Keyswitch zone types to set and unset the system.
•
Presetting indication and any automatic override of set
prevention.
Refer to Table 6 below for all supported options for notification
requirements.
Table 6: EN 50131-1:2006 options
Notification
equipment (Alarm
reporting) Grade 3 options
A B C D
Remotely powered
audible WD 2 Optional Optional Optional
Self-powered audible
WD Optional 1 Optional Optional
Main ATS [1] ATS 4 ATS 4 ATS 4 ATS 5
Additional ATS [1] Optional Optional ATS 3 Optional
ATS [2] SP3 SP3 DP3 [3] SP4
[1] Requirement according to EN 50136:2010
[2] Requirement according to EN 50136:2012
[3] Primary Path
— SP4, backup path — SP2
Legend:
•
ATS: Alarm transmission system
•
SP: Single path alarm transmission system
•
DP: Dual path alarm transmission system
The key variations of cards and keys are the following:
•
ATS147x range (used with ATS1135 and ATS119x):
67 million
•
ATS145x card range (used with ATS1136 and ATS118x):
280 trillion
The cards make use of 26 bit (to 48 bit) Hitag protocol.
The installer (user level 3) commissions the system with
appropriate additional functions.
The end-user (user level 2) is able to make use of all these
functions.
The Installer can only make use of these functions when he
has an access granted by end-user.
EN 50136 policy
Required settings:
•
9.1.n.7 Retry count: 1
•
9.1.n.8.3.2 Heartbeat time: According Table 7 on page 14.
•
9.1.n.8.3.5 Freq. HB time: According Table 7 on page 14.
•
9.3.n.8.1 Firewall: Yes
•
9.3.n.8.2 Reply on PING: No
•
9.3.n.7.6.1 Firewall: Yes
•
9.3.n.7.6.2 Reply on PING: No
•
9.3.n.9 Encryption: Yes
•
9.4.3 Encryption key 1 must be set.
See also “Transmitter polling interval requirements” below.
Transmitter polling interval requirements
Transmitter polling interval must be set according to specified
requirements for different alarm transmission systems (ATS).
Table 7 on page 14 lists all required settings for the
appropriate standards and diallers.