Ariston PK 640 R GH AUS Скачать руководство пользователя страница 3

AUS

3

Adjacent cabinetry

The location of connection points is given in the
table on page 5 . For trouble-free operation of
appliances installed in housing units, the minimum
distances shown in fig.4 should be observed.  It is
recommended that the adjacent kitchen surfaces
should be capable of withstanding temperatures of
65°C. Also, the following must be observed:
• The appliance should be installed next to

cabinetry which is no taller than the top of the
cooker hob.

• The wall in direct contact with the back panel of

the cooker must be made of non-flammable
material.  During operation of the cooker, the back
panel of the cooker could reach a temperature of
50°C above room temperature.

• Kitchen cabinets installed next to the cooker that

are higher than the top of the hob, must be at
least 600 mm from the edge of the hob itself.

• If the hood is installed below a wall cabinet, the

latter must be at least 700 mm (millimetres) above
the surface of the hob.

• Cabinets installed adjacent to the hood must be

at least 420 mm above the hob,

The following minimum
clearances to combustible
materials must be observed:
• Minimum clearance from
edge of burner to side wall
must be 200 mm.
• Minimum clearance from
edge of burner to rear wall
must be 55 mm.

Range hoods

Range hoods and overhead exhaust fans must be
installed according to manufacturers’ instructions
but in no case shall clearance from hob burners be
less than 600 mm for range hoods and 750 mm for
overhead exhaust fans.
• If the hood is installed below a wall cabinet, the

latter must be at least 700 mm (millimetres) above
the surface of the hob.

Fitting the cooktop above an oven

When installing the cooktop above an oven, both the
electricity supply cable and the gas pipe or flexible
hose must not touch hot parts of the oven housing.
When installing above a built-under oven without
forced cooling ventilation, suitable air vents should
be provided for (inlet at least 200 cm² from the
bottom, outlet at least 120 cm² from the top part) to
allow adequate ventilation inside the housing unit.
Also a wooden panel should be installed beneath
the hob as insulation, positioning it at a minimum
distance of 15 mm from the hob housing

• The installation cavity should have the dimensions

indicated in the figure. Fastening hooks are provided,
allowing you to fasten the hob to tops that are between
20 and 40 mm thick. To ensure the hob is securely
fastened to the top, we recommend you use all the
hooks provided.

555 mm

55 mm

475 mm

Hook fastening diagram

Hooking position

Hooking position

for top

 H=20 mm

for top 

H=30 mm

Front

Hooking position

Back

for top

 H=40 mm

!

 Use the hooks contained in the “accessory pack”

• Where the hob is not installed over a built-in oven, a

wooden panel must be installed as insulation. This
must be placed at a minimum distance of 20 mm from
the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the
cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
completely flat surface with an opening of at least 45 x
560 mm (

see diagrams).

600mm min.

420mm min.

700mm min.

Содержание PK 640 R GH AUS













































Отзывы: