Ariens 911088 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 22

Ariens 911088 Скачать руководство пользователя страница 13

GB - 13

3. Push primer bulb 2 or 3 times for a cold

engine (911088, 091).

NOTE:

It is unnecessary to prime a warm

engine.

4. Pull throttle control all the way back to

Fast position (911088, 091).
Push throttle control to the choke position
(911096, 097).

5. With engine/blade control held against

the handlebar, grasp starter handle and
pull rope slowly until it pulls harder. This
is the compression stroke. Let rope
rewind slowly.

6. Pull rope with rapid continuous full arm

stroke to start engine. Allow rope to
rewind slowly.

IMPORTANT:

DO NOT let starter handle snap

against bracket.

7. Repeat steps 4 and 5 until engine starts.

(If engine does not start, refer to

Troubleshooting

.)

8. After engine starts, pull throttle control to

the Fast position (911096, 097).

Shut Off

1. Release wheel drive control and allow

unit to stop completely (self-propelled
models).

2. Release engine/blade control.

Mowing Tips

Cut grass when it is dry.
Keep mower blades sharp.
Do not set cutting height too low. For tall grass,
mow twice.
Do not mow too fast.
Mow with engine at full throttle.
Vary cutting pattern with each mowing.

NOTE:

To prevent dirt and grass from

collecting on mower pan, avoid operating over
bare ground with only patches of grass.

Mulching Tips

For best mulching performance, cut no more
than 1 inch of grass per cutting.

Ariens Dealers will provide any service, parts
or adjustments which may be required to keep
your unit operating at peak efficiency. Should
engine require service, contact an Ariens
dealer or an authorized engine manufacturer's
service center.

MAINTENANCE SCHEDULE

NOTE:

Some working conditions (heavy

loads, high ambient temperatures, dusty
conditions, or airborne debris) may require
more frequent service.
See engine manual for further maintenance
and troubleshooting information.

After first 5 Hours of operation

CHECK ENGINE/BLADE
CONTROL

The engine and blade must stop within 3
seconds after releasing the control. If the
engine and blade continue to run, adjust or
repair control immediately.

MAINTENANCE

CAUTION:

AVOID INJURY. Read

and understand entire

Safety

section

before proceeding.

MAINTENANCE SCHEDULE

Service Performed

Before

Each

Use

25

100

Check Engine/Blade
Control

•

Check Wheel Drive
Control

•

Check Grass
Collector

•

Clean Unit

•

Check Engine Oil

•

Check Mower Blade

•

Check Drive Belt

•

Check Fasteners

•

Check Air Cleaner

•

Change Engine Oil

•

General Lubrication

•

Check Spark Plug

•

Check Engine
Cooling

•

Check Muffler

•

*

*

«
...
11
12
13
14
15
...
»

Содержание 911088























Отзывы:

Нет отзывов