Aria Aria-130 Скачать руководство пользователя страница 141

Страница: 141 / 163

Aria-130 Digital Key Telephone System

Issue: 1.2

Installation Manual

141



The LCD displays call information and the status of terminal.



The keypad contains specially labeled keys assisting users to make calls and operate telephone

features.

Subscription

The wireless terminals associate unique identities, to prevent unauthorized use of the PSTN line. See the

User Guide of the GDC-33xH and GDC-340H for the subscription of wireless terminals.

LCD Display

The GDC-33xH has a three-line display (6 icons & 20 characters) for alphanumeric information and the

GDC-340H has a three-line display (8 icons & 24 characters) for alphanumeric information.

(a) GDC-33xH (b) GDC-340H

Figure 5.3.5 The LCD Display

Security

The wireless terminal ciphers voice information before transmitting it. It ensures that the conversations

are private and inaccessible to electronic eavesdropping.

Ringing

There are various types of ring signal in the wireless terminal and users can select the ring signal and

control the volume of ring signal. Seven volume levels are available in GDC-335xH and four volume

levels are available in GDC-340H.

Key Pad Tone

A beep is heard when the wireless terminals recognize a dial input from dial pad.

Low Battery Alarm

When the battery is discharged to low battery state, the low battery message is displayed in the display

LCD of the wireless terminal (except GDC-340H) and warning tone is heard (both GDC-33xH and GDC-

340H).

Removable Battery Pack

The GDC-33xH has one type of battery pack (330-SBP, 600mAh). It is standard battery pack.

The GDC-340H has standard rechargeable battery (1.2V rechargeable NiMH AAA size 2 cell).

Antenna

The antenna of the GDC-33xH is an wire and non-retractable antenna.

Do not extract it.

If you try to pull

it out, it may be destroyed. The antenna of the GDC-340H is embedded.

Holes of Top and Bottom Side

There are two holes in the top and bottom side of a GDC-33xH. The holes are special purpose and are

covered with covers. Do not take off these covers.

Содержание Aria-130




































































































































































Результаты поиска

Содержание Aria-130

Отзывы:

Похожие инструкции для Aria-130

Бренды по названию

Популярные бренды

Aria Aria-130, Руководство по установке

Результаты поиска

Содержание Aria-130

Отзывы:

Похожие инструкции для Aria-130

Бренды по названию

Популярные бренды