Argus ALPHA OUTBACK ENERGY Cordex 48-1kW, Инструкция по эксплуатации

Страница: 29 / 46

030-713-C0 Rev A WC
Page 15 of 23
6.11 Alarm and Signal Wiring Connections for CXCM
NOTE: To aid the user with installation, frequent reference is made to drawings located at the rear of this manual.
Custom configurations may be detailed within the Argus power system documentation package.
For terminal block connections, the recommended wire sizes are 0.823 to 0.129mm
2
(#18 to #26 AWG) for the
temperature range of 0 to 50 deg. C (as per UL/CSA).
For insulation displacement receptacles, the recommended wire size is #18 AWG.
CAUTION: to reduce risk of fire, use only 0.129mm
2
(#26 AWG) or larger wire.
Terminal Description Signal Type Range
Alarm Outputs –
Can be configured to de-energize on alarm (DOA) or energize on alarm (EOA).
#2-21,22(common) K2, LVD2 NC/COM/NO (JP2) 60Vdc / 1A
#3-19,20(common) K3, LVD3 NC/COM/NO (JP3) 60Vdc / 1A
#4-17,18(common) K4, System Minor NC/COM/NO (JP4) 60Vdc / 1A
#5-15,16(common) K5, System Major NC/COM/NO (JP5) 60Vdc / 1A
#6-13,14(common) K6, AC Mains Hi-Low NC/COM/NO (JP6) 60Vdc / 1A
#7-11,12(common) K7, Not assigned NC/COM/NO (JP7) 60Vdc / 1A
#8-9,10(common) K8, Not assigned NC/COM/NO (JP8) 60Vdc / 1A
#0-25,24,23 K0, System Fail Output* NC/COM/NO 60Vdc / 1A
Digital Inputs –
See Table B for definitions of logic and system
P5-1,2 D1, Distribution Fuse (Alarm) Pos (+) or Neg (-) 0—60Vdc
P5-3, P6-1 D2, Distribution CB (Alarm) Pos (+) or Neg (-) 0—60Vdc
P6-2,3 D3, Battery CB (Alarm) Pos (+) or Neg (-) 0—60Vdc
Analog Inputs and System Signals
E1 Battery -48V** Neg (-) 20—60Vdc
J3 Ethernet port N/A N/A
P1-2,1 K1, LVD1 Pos (+) / Neg (-) 0—60Vdc / 1A
P7-2,1 V1, Load Voltage Pos (+) / Neg (-) 0—100Vdc
P8-2,1 I1, Load Current Pos (+) / Neg (-) ±50mV
–
for List 120, add the following:
1-2 T1 (GP1), Temp Probe 1 Pos (+) / Neg (-) 0—20Vdc
, with power source
3-4 T2 (GP2), Temp Probe 2 Pos (+) / Neg (-)
0—20Vdc
, with power source
5-6 GP3, General Input 3 Pos (+) / Neg (-) Not used
7-8 GP4, General Input 4 Pos (+) / Neg (-) ±60V,
bi-polar voltage
–
for List 124, consult the factory to add the following:
1-2 V3 (GP1), Voltage Input 3 Pos (+) / Neg (-) 0—60Vdc
3-4 V4 (GP2), Voltage Input 4 Pos (+) / Neg (-) 0—60Vdc
5-6 V5 (GP3), Voltage Input 5 Pos (+) / Neg (-) 0—60Vdc
7-8 T1 (GP4), General Input 4 Pos (+) / Neg (-)
0—20Vdc
, with power source
Table A–Signal wiring connections for CXCM
* System Fail output relay is fail-safe and will de-energize during an alarm condition.
** Battery –48V: connect to battery only when using a battery disconnect device
NOTE: To aid the user with installation, frequent reference is made to drawings located at the rear of this manual.
Custom configurations may be detailed within the Argus power system documentation package.