background image

Issue 1 25/2/2019  

11 

Care instructions 

 

The  glass  cover  can  be  removed  from  the  light  fitting  and  washed  in 
warm  soapy  water.    Ensure  it  is  dried  thoroughly  before  refitting.    Do 
not use abrasives as these may scratch the surface. 

 

Wipe external surfaces of the light fitting with a soft dry or slightly damp 
cloth.  Do  not  use  abrasives  as  these  may  scratch  the  surface  and 
NEVER use a wet cloth or immerse in water.

 

 

 

Technical specification 

 

 
 

Recycling electrical products 

This marking indicates that this product should not be disposed 
with  other  household  wastes  throughout  the  EU.  To  prevent 
possible  harm  to  the  environment  or  human  health  from 
uncontrolled  waste  disposal,  recycle  it  responsibly  to  promote 
the  sustainable  reuse  of  material  resources.  To  return  your 
used  device,  please  use  the  return  and  collection  systems  or 
contact the retailer where the product was purchased. They can 
take this product for environmental safe recycling. 
 
 
 
 
 
 
 

 

If you encounter any problems with 
this product please call our 
customer care team on  
0345 640 30 30 

Produced in China for 
Argos Limited, 
489 

– 499 Avebury Boulevard 

Central Milton Keynes

 

MK9 2NW. UK. 

 

Cat No: 

8848628 

Model 

G03131P 

Rated voltage 

220 - 240V ~ 50Hz 

Class rating 

1 (earthed) 

Recommend bulb 
wattage 

Max 60W ES GLS 

8 - 10W ES LED (energy saving) 

Содержание G03131P












Отзывы: