manualshive.com logo in svg

Argo ADG ECO PLUS 100PH, Руководство по установке

Поделиться
Скачать
Argo ADG ECO PLUS 100PH Скачать руководство пользователя страница 68

Duct Type Unit

 

64 

(4) Pump down refrigerant system, if possible.
(5) If a vacuum is not possible, make a manifold so that refrigerant can be

removed from various parts of the system.

(6) Make sure that cylinder is situated on the scales before recovery takes

place.

(7) Start  the  recovery  machine  and  operate  in  accordance  with

manufacturer's instructions.

(8) Do not overfill cylinders. (No more than 80 % volume liquid charge).
(9) Do  not  exceed  the  maximum  working  pressure  of  the  cylinder,  even

temporarily.

(10) When the cylinders have been filled correctly and the process completed,

make sure that the cylinders and the equipment are removed from site
promptly and all isolation valves on the equipment are closed off.

(11) Recovered  refrigerant  shall  not  be  charged  into  another  refrigeration

system unless it has been cleaned and checked.

5.4.9 Labelling 

Equipment  shall  be  labelled  stating  that  it  has  been  de-commissioned  and 

emptied of refrigerant. The label shall be dated and signed. Ensure that there are 
labels on the equipment stating the equipment contains flammable refrigerant. 

5.4.10 Recovery 

When  removing  refrigerant  from  a  system,  either  for  servicing  or 

decommissioning,  it  is  recommended  good  practice  that  all  refrigerants  are 
removed safely. 

When  transferring  refrigerant  into  cylinders,  ensure  that  only  appropriate 

refrigerant  recovery  cylinders  are  employed.  Ensure  that  the  correct  number  of 
cylinders for holding the total system charge are available. All cylinders to be used 
are  designated  for  the  recovered  refrigerant  and  labelled  for  that  refrigerant  (i.e. 
special cylinders for the recovery of refrigerant). 

Cylinders shall be complete with pressure relief valve and associated shut-off 

valves  in  good  working  order.  Empty  recovery  cylinders  are  evacuated  and,  if 
possible, cooled before recovery occurs. 

The  recovery  equipment  shall  be  in  good  working  order  with  a  set  of 

instructions concerning the equipment that is at hand and shall be suitable for the 

Содержание ADG ECO PLUS 100PH







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды